Giter Club home page Giter Club logo

mt798x-wrt_relese's People

Contributors

zqinking avatar

Stargazers

 avatar  avatar  avatar  avatar  avatar  avatar  avatar  avatar  avatar  avatar  avatar  avatar

Watchers

 avatar  avatar

mt798x-wrt_relese's Issues

JDC AX1800 Pro 刷入後無限重啟

Uboot: uboot-JDC_AX1800_Pro-AX6600_Athena-20240510.bin
分區表: gpt-JDC_AX1800_Pro_dual-boot_rootfs2048M_no-last-partition.bin

這個是分區表:

Disk /dev/mmcblk0: 114.73 GiB, 123195097088 bytes, 240615424 sectors
Units: sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disklabel type: gpt
Disk identifier: 98101B32-BBE2-4BF2-A06E-2BB33D000C20

Device            Start       End   Sectors   Size Type
/dev/mmcblk0p1       34      1569      1536   768K unknown
/dev/mmcblk0p2     1570      2081       512   256K unknown
/dev/mmcblk0p3     2082      2593       512   256K unknown
/dev/mmcblk0p4     2594      6177      3584   1.8M unknown
/dev/mmcblk0p5     6178      9761      3584   1.8M unknown
/dev/mmcblk0p6     9762     10273       512   256K unknown
/dev/mmcblk0p7    10274     10785       512   256K unknown
/dev/mmcblk0p8    10786     11297       512   256K unknown
/dev/mmcblk0p9    11298     11809       512   256K unknown
/dev/mmcblk0p10   11810     12321       512   256K unknown
/dev/mmcblk0p11   12322     12833       512   256K unknown
/dev/mmcblk0p12   12834     13345       512   256K unknown
/dev/mmcblk0p13   13346     14625      1280   640K unknown
/dev/mmcblk0p14   14626     15905      1280   640K unknown
/dev/mmcblk0p15   15906     16417       512   256K unknown
/dev/mmcblk0p16   16418     28705     12288     6M unknown
/dev/mmcblk0p17   28706     40993     12288     6M unknown
/dev/mmcblk0p18   40994   4235297   4194304     2G unknown
/dev/mmcblk0p19 4235298   4243489      8192     4M unknown
/dev/mmcblk0p20 4243490   4366369    122880    60M unknown
/dev/mmcblk0p21 4366370   4374561      8192     4M unknown
/dev/mmcblk0p22 4374562   4415521     40960    20M unknown
/dev/mmcblk0p23 4415522   4416545      1024   512K unknown
/dev/mmcblk0p24 4416546   4595745    179200  87.5M unknown
/dev/mmcblk0p25 4595746   5210145    614400   300M unknown
/dev/mmcblk0p26 5210146   6258721   1048576   512M unknown
/dev/mmcblk0p27 6258722 240615390 234356669 111.7G unknown

在 uboot 刷入 libwrt-qualcommax-ipq60xx-jdcloud_ax1800-pro-squashfs-factory.bin 後會無限重啟

tty 讀到這些 log

MMC read: dev # 0, block # 16418, count 12288 ... 12288 blocks read: OK
## Loading kernel from FIT Image at 44000000 ...
   Using 'config@cp03-c2' configuration
   Trying 'kernel-1' kernel subimage
     Description:  ARM64 OpenWrt Linux-6.6.41
     Type:         Kernel Image
     Compression:  gzip compressed
     Data Start:   0x440000e8
     Data Size:    5299327 Bytes = 5.1 MiB
     Architecture: AArch64
     OS:           Linux
     Load Address: 0x41000000
     Entry Point:  0x41000000
     Hash algo:    crc32
     Hash value:   18ae5d2f
     Hash algo:    sha1
     Hash value:   39ae2bce9f181ba9139af9c2dc722f84c0751264
   Verifying Hash Integrity ... crc32+ sha1+ OK
## Loading fdt from FIT Image at 44000000 ...
   Using 'config@cp03-c2' configuration
   Trying 'fdt-1' fdt subimage
     Description:  ARM64 OpenWrt jdcloud_ax1800-pro device tree blob
     Type:         Flat Device Tree
     Compression:  uncompressed
     Data Start:   0x4450deac
     Data Size:    38201 Bytes = 37.3 KiB
     Architecture: AArch64
     Hash algo:    crc32
     Hash value:   c24151c1
     Hash algo:    sha1
     Hash value:   e203c8efdd69eaad0256eadbbef32d9491298e6a
   Verifying Hash Integrity ... crc32+ sha1+ OK
   Booting using the fdt blob at 0x4450deac
   Uncompressing Kernel Image ... OK
   Loading Device Tree to 484f3000, end 484ff538 ... OK
Could not find PCI in device tree
Using machid 0x8030201 from environment

Starting kernel ...

Jumping to AARCH64 kernel via monitor
[    0.000000] Booting Linux on physical CPU 0x0000000000 [0x51af8014]
[    0.000000] Linux version 6.6.41 (zqinking@zqinking) (aarch64-openwrt-linux-musl-gcc (OpenWrt GCC 13.3.0 r0-0a9b3b2) 13.3.0, GNU ld (GNU Binutils) 2.42) #0 SMP PREEMPT Fri Jul 19 13:19:23 2024
[    0.000000] Machine model: JDCloud AX1800 Pro
[    0.000000] OF: reserved mem: 0x0000000000060000..0x0000000000065fff (24 KiB) nomap non-reusable memory@60000
[    0.000000] OF: reserved mem: 0x0000000040000000..0x0000000040ffffff (16384 KiB) nomap non-reusable nss@40000000
[    0.000000] OF: reserved mem: 0x000000004a100000..0x000000004a4fffff (4096 KiB) nomap non-reusable bootloader@4a100000
[    0.000000] OF: reserved mem: 0x000000004a600000..0x000000004a9fffff (4096 KiB) nomap non-reusable memory@4a600000
[    0.000000] OF: reserved mem: 0x000000004aa00000..0x000000004aafffff (1024 KiB) nomap non-reusable memory@4aa00000
[    0.000000] OF: reserved mem: 0x000000004ab00000..0x000000004e1fffff (56320 KiB) nomap non-reusable memory@4ab00000
[    0.000000] OF: reserved mem: 0x000000004e200000..0x000000004e2fffff (1024 KiB) nomap non-reusable ramoops@50000000
[    0.000000] OF: reserved mem: 0x0000000050000000..0x00000000500fffff (1024 KiB) nomap non-reusable q6_etr_dump@50000000
[    0.000000] OF: reserved mem: 0x0000000050100000..0x00000000501fffff (1024 KiB) nomap non-reusable m3_dump@50100000
[    0.000000] Zone ranges:
[    0.000000]   DMA      [mem 0x0000000040000000-0x000000005fffffff]
[    0.000000]   DMA32    empty
[    0.000000]   Normal   empty
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000040000000-0x0000000040ffffff]
[    0.000000]   node   0: [mem 0x0000000041000000-0x000000004a0fffff]
[    0.000000]   node   0: [mem 0x000000004a100000-0x000000004a4fffff]
[    0.000000]   node   0: [mem 0x000000004a500000-0x000000004a5fffff]
[    0.000000]   node   0: [mem 0x000000004a600000-0x000000004e2fffff]
[    0.000000]   node   0: [mem 0x000000004e300000-0x000000004fffffff]
[    0.000000]   node   0: [mem 0x0000000050000000-0x00000000501fffff]
[    0.000000]   node   0: [mem 0x0000000050200000-0x000000005fffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x000000005fffffff]
[    0.000000] psci: probing for conduit method from DT.
[    0.000000] psci: PSCIv1.0 detected in firmware.
[    0.000000] psci: Using standard PSCI v0.2 function IDs
[    0.000000] psci: MIGRATE_INFO_TYPE not supported.
[    0.000000] psci: SMC Calling Convention v1.0
[    0.000000] percpu: Embedded 19 pages/cpu s37224 r8192 d32408 u77824
[    0.000000] Detected VIPT I-cache on CPU0
[    0.000000] CPU features: detected: Spectre-v4
[    0.000000] alternatives: applying boot alternatives
[    0.000000] Kernel command line: console=ttyMSM0,115200n8 root=PARTUUID=49ce1048-1499-ae66-4240-f15d706a2598 gpt rootwait rootfstype=squashfs,ext4 swiotlb=1 coherent_pool=2M swiotlb=1
[    0.000000] Dentry cache hash table entries: 65536 (order: 7, 524288 bytes, linear)
[    0.000000] Inode-cache hash table entries: 32768 (order: 6, 262144 bytes, linear)
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 129024
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] software IO TLB: area num 4.
[    0.000000] software IO TLB: SWIOTLB bounce buffer size roundup to 1MB
[    0.000000] software IO TLB: mapped [mem 0x000000005f4c0000-0x000000005f5c0000] (1MB)
[    0.000000] Memory: 414184K/524288K available (8256K kernel code, 940K rwdata, 2456K rodata, 1600K init, 306K bss, 110104K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] rcu: Preemptible hierarchical RCU implementation.
[    0.000000]  Trampoline variant of Tasks RCU enabled.
[    0.000000]  Tracing variant of Tasks RCU enabled.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 100 jiffies.
[    0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[    0.000000] Root IRQ handler: gic_handle_irq
[    0.000000] GICv2m: range[mem 0x0b00a000-0x0b00affc], SPI[448:479]
[    0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[    0.000000] arch_timer: cp15 and mmio timer(s) running at 24.00MHz (virt/virt).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[    0.000000] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[    0.000075] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=24000)
[    0.000089] pid_max: default: 32768 minimum: 301
[    0.005448] Mount-cache hash table entries: 1024 (order: 1, 8192 bytes, linear)
[    0.005462] Mountpoint-cache hash table entries: 1024 (order: 1, 8192 bytes, linear)
[    0.009988] RCU Tasks: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1.
[    0.010111] RCU Tasks Trace: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1.
[    0.010331] rcu: Hierarchical SRCU implementation.
[    0.010335] rcu:     Max phase no-delay instances is 400.
[    0.011168] smp: Bringing up secondary CPUs ...
[    0.011881] Detected VIPT I-cache on CPU1
[    0.011981] CPU1: Booted secondary processor 0x0000000001 [0x51af8014]
[    0.012761] Detected VIPT I-cache on CPU2
[    0.012832] CPU2: Booted secondary processor 0x0000000002 [0x51af8014]
[    0.013557] Detected VIPT I-cache on CPU3
[    0.013624] CPU3: Booted secondary processor 0x0000000003 [0x51af8014]
[    0.013698] smp: Brought up 1 node, 4 CPUs
[    0.013706] SMP: Total of 4 processors activated.
[    0.013711] CPU features: detected: 32-bit EL0 Support
[    0.013716] CPU features: detected: CRC32 instructions
[    0.013786] CPU features: emulated: Privileged Access Never (PAN) using TTBR0_EL1 switching
[    0.013794] CPU: All CPU(s) started at EL1
[    0.013797] alternatives: applying system-wide alternatives
[    0.022588] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns
[    0.022614] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[    0.024420] pinctrl core: initialized pinctrl subsystem
[    0.026761] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[    0.027741] DMA: preallocated 2048 KiB GFP_KERNEL pool for atomic allocations
[    0.028057] DMA: preallocated 2048 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
[    0.028380] DMA: preallocated 2048 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
[    0.028760] thermal_sys: Registered thermal governor 'step_wise'
[    0.028855] cpuidle: using governor menu
[    0.029117] ASID allocator initialised with 65536 entries
[    0.080052] Modules: 29344 pages in range for non-PLT usage
[    0.080064] Modules: 520864 pages in range for PLT usage
[    0.081662] cryptd: max_cpu_qlen set to 1000
[    0.085582] SCSI subsystem initialized
[    0.085789] usbcore: registered new interface driver usbfs
[    0.085825] usbcore: registered new interface driver hub
[    0.085866] usbcore: registered new device driver usb
[    0.086196] qcom_scm: convention: smc arm 64
[    0.087765] clocksource: Switched to clocksource arch_sys_counter
[    0.091958] NET: Registered PF_INET protocol family
[    0.092114] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear)
[    0.094330] tcp_listen_portaddr_hash hash table entries: 256 (order: 0, 4096 bytes, linear)
[    0.094387] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[    0.094406] TCP established hash table entries: 4096 (order: 3, 32768 bytes, linear)
[    0.094454] TCP bind hash table entries: 4096 (order: 5, 131072 bytes, linear)
[    0.094601] TCP: Hash tables configured (established 4096 bind 4096)
[    0.094705] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[    0.094731] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[    0.095065] NET: Registered PF_UNIX/PF_LOCAL protocol family
[    0.095105] PCI: CLS 0 bytes, default 64
[    0.097274] workingset: timestamp_bits=46 max_order=17 bucket_order=0
[    0.097856] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.097864] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.154060] qcom-qmp-usb-phy 78000.ssphy: supply vdda-phy not found, using dummy regulator
[    0.154246] qcom-qmp-usb-phy 78000.ssphy: supply vdda-pll not found, using dummy regulator
[    0.156064] qcom-qusb2-phy 59000.qusb: supply vdd not found, using dummy regulator
[    0.156249] qcom-qusb2-phy 59000.qusb: supply vdda-pll not found, using dummy regulator
[    0.156295] qcom-qusb2-phy 59000.qusb: supply vdda-phy-dpdm not found, using dummy regulator
[    0.156496] qcom-qusb2-phy 59000.qusb: Registered Qcom-QUSB2 phy
[    0.156805] qcom-qusb2-phy 79000.qusb: supply vdd not found, using dummy regulator
[    0.156952] qcom-qusb2-phy 79000.qusb: supply vdda-pll not found, using dummy regulator
[    0.157016] qcom-qusb2-phy 79000.qusb: supply vdda-phy-dpdm not found, using dummy regulator
[    0.157228] qcom-qusb2-phy 79000.qusb: Registered Qcom-QUSB2 phy
[    0.167128] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[    0.168357] msm_serial 78b1000.serial: msm_serial: detected port #0
[    0.168397] msm_serial 78b1000.serial: uartclk = 1843200
[    0.168786] 78b1000.serial: ttyMSM0 at MMIO 0x78b1000 (irq = 21, base_baud = 115200) is a MSM
[    0.168820] msm_serial: console setup on port #0
[    0.168901] printk: console [ttyMSM0] enabled
[    1.007150] msm_serial: driver initialized
[    1.016858] loop: module loaded
[    1.018249] spi_qup 78b5000.spi: IN:block:16, fifo:64, OUT:block:16, fifo:64
[    1.019915] spi-nor spi0.0: unrecognized JEDEC id bytes: 00 00 00 00 00 00
[    1.042408] i2c_dev: i2c /dev entries driver
[    1.047845] sdhci: Secure Digital Host Controller Interface driver
[    1.047894] sdhci: Copyright(c) Pierre Ossman
[    1.052967] sdhci-pltfm: SDHCI platform and OF driver helper
[    1.058879] mmc0: CQHCI version 5.10
[    1.059713] remoteproc remoteproc0: releasing cd00000.remoteproc
[    1.069931] NET: Registered PF_INET6 protocol family
[    1.073780] Segment Routing with IPv6
[    1.077650] In-situ OAM (IOAM) with IPv6
[    1.081215] NET: Registered PF_PACKET protocol family
[    1.085188] Bridge firewalling registered
[    1.090242] l2tp_core: L2TP core driver, V2.0
[    1.093803] mmc0: SDHCI controller on 7804000.mmc [7804000.mmc] using ADMA 64-bit
[    1.094087] l2tp_netlink: L2TP netlink interface
[    1.098504] sdhci_msm 7804000.mmc: mmc0: CQE init: success
[    1.105927] 8021q: 802.1Q VLAN Support v1.8
[    1.154169] cpufreq: cpufreq_online: CPU0: Running at unlisted initial frequency: 799999 KHz, changing to: 864000 KHz
[    1.156152] remoteproc remoteproc0: cd00000.remoteproc is avai�[    1.170571] Waiting for root device PARTUUID=49ce1048-1499-ae66-4240-f15d706a2598...
[    1.225690] mmc0: Command Queue Engine enabled
[    1.225719] mmc0: new HS200 MMC card at address 0001
[    1.229608] mmcblk0: mmc0:0001 SLD128 115 GiB
[    1.263396] Alternate GPT is invalid, using primary GPT.
[    1.263460]  mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17 p18 p19 p20 p21 p22 p23 p24 p25 p26
[    1.269802] mmcblk0boot0: mmc0:0001 SLD128 4.00 MiB
[    1.278911] mmcblk0boot1: mmc0:0001 SLD128 4.00 MiB
[    1.283224] mmcblk0rpmb: mmc0:0001 SLD128 4.00 MiB, chardev (247:0)
[    1.296392] VFS: Mounted root (squashfs filesystem) readonly on device 179:18.
[    1.297162] Freeing unused kernel memory: 1600K
[    1.302690] Run /sbin/init as init process
[    1.446988] init: Console is alive
[    1.447131] init: - watchdog -
[    2.183819] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    2.228123] gpio_button_hotplug: loading out-of-tree module taints kernel.
[    2.263272] ssdk_dt_parse_interrupt[941]:INFO:intr-gpio does not exist
[    2.585138] __adpt_hppe_uniphy_psgmii_mode_set[1194]:INFO:uniphy 0 psgmii channel selection
[    2.693877] regi_init[2525]:INFO:Initializing CPPE Done!!
[    2.693984] regi_init[2574]:INFO:qca-ssdk module init succeeded!
[    2.700203] EDMA ver 1 hw init
[    2.704575] EDMA HW Reset completed succesfully
[    2.707220] Num rings - TxDesc:1 (23-23) TxCmpl:1 (23-23)
[    2.711623] RxDesc:1 (15-15) RxFill:1 (7-7)
[    2.717625] dp2: ppe offload disabled: 0 for macid 2
[    2.721168] dp2: Switch attached to macid 2 status: 0
[    2.881463] Qualcomm QCA8075 90000.mdio-1:01: attached PHY driver (mii_bus:phy_addr=90000.mdio-1:01, irq=POLL)
[    2.882388] dp3: ppe offload disabled: 0 for macid 3
[    2.890365] dp3: Switch attached to macid 3 status: 0
[    2.948069] Qualcomm QCA8075 90000.mdio-1:02: attached PHY driver (mii_bus:phy_addr=90000.mdio-1:02, irq=POLL)
[    2.948958] dp4: ppe offload disabled: 0 for macid 4
[    2.956966] dp4: Switch attached to macid 4 status: 0
[    3.015070] Qualcomm QCA8075 90000.mdio-1:03: attached PHY driver (mii_bus:phy_addr=90000.mdio-1:03, irq=POLL)
[    3.015982] dp5: ppe offload disabled: 0 for macid 5
[    3.023966] dp5: Switch attached to macid 5 status: 0
[    3.082072] Qualcomm QCA8075 90000.mdio-1:04: attached PHY driver (mii_bus:phy_addr=90000.mdio-1:04, irq=POLL)
[    3.082938] **********************************************************
[    3.090989] * NSS Data Plane driver
[    3.097469] **********************************************************
[    3.108657] phy phy-59000.qusb.1: QUSB2PHY pll lock failed: status reg = 10
[    3.108703] phy phy-59000.qusb.1: phy init failed --> -16
[    3.114442] dwc3 7000000.usb: error -EBUSY: failed to initialize core
[    3.120029] dwc3: probe of 7000000.usb failed with error -16
[    3.133964] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[    3.134016] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 1
[    3.139350] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220fe65 hci version 0x110 quirks 0x0000008000000010
[    3.145998] xhci-hcd xhci-hcd.1.auto: irq 39, io mem 0x08a00000
[    3.155408] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[    3.161197] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 2
[    3.166745] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed
[    3.174661] hub 1-0:1.0: USB hub found
[    3.180905] hub 1-0:1.0: 1 port detected
[    3.184946] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[    3.189027] hub 2-0:1.0: USB hub found
[    3.196786] hub 2-0:1.0: 1 port detected
[    3.202672] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    3.211617] init: - preinit -
[    4.473769] random: crng init done
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[    6.755557] mount_root: loading kmods from internal overlay
[    6.769882] kmodloader: loading kernel modules from //etc/modules-boot.d/*
[    6.770835] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
[    7.109526] block: attempting to load /tmp/overlay/upper/etc/config/fstab
[    7.109635] block: unable to load configuration (fstab: Entry not found)
[    7.115420] block: attempting to load /tmp/overlay/etc/config/fstab
[    7.122197] block: unable to load configuration (fstab: Entry not found)
[    7.128109] block: attempting to load /etc/config/fstab
[    7.137623] block: unable to load configuration (fstab: Entry not found)
[    7.139997] block: no usable configuration
[    7.147082] block: attempting to load /etc/config/fstab
[    7.150856] block: unable to load configuration (fstab: Entry not found)
[    7.155964] block: no usable configuration
[    7.163486] loop0: detected capacity change from 0 to 4194304
[    7.172770] loop0: detected capacity change from 4194304 to 4053248
[    7.173888] mount_root: overlay filesystem in /dev/loop0 has not been formatted yet
[    7.940449] F2FS-fs (loop0): Found nat_bits in checkpoint
[    7.958050] F2FS-fs (loop0): Mounted with checkpoint version = 8f5dc87
[    8.222212] block: attempting to load /tmp/overlay/upper/etc/config/fstab
[    8.222313] block: unable to load configuration (fstab: Entry not found)
[    8.228119] block: attempting to load /tmp/overlay/etc/config/fstab
[    8.234865] block: unable to load configuration (fstab: Entry not found)
[    8.240802] block: attempting to load /etc/config/fstab
[    8.247815] block: unable to load configuration (fstab: Entry not found)
[    8.252686] block: no usable configuration
[    8.259765] block: attempting to load /etc/config/fstab
[    8.263542] block: unable to load configuration (fstab: Entry not found)
[    8.268652] block: no usable configuration
[    8.276285] mount_root: overlay filesystem has not been fully initialized yet
[    8.279784] mount_root: switching to f2fs overlay
[    8.290258] overlayfs: null uuid detected in lower fs '/', falling back to xino=off,index=off,nfs_export=off.
[    8.362096] urandom-seed: Seed file not found (/etc/urandom.seed)
[    8.388414] procd: - early -
[    8.388506] procd: - watchdog -
[    8.927811] procd: - watchdog -
[    8.942535] procd: - ubus -
[    9.095721] procd: - init -
Please press Enter to activate this console.
[    9.422159] kmodloader: loading kernel modules from /etc/modules.d/*
[    9.453977] tun: Universal TUN/TAP device driver, 1.6
[    9.526381] urngd: v1.0.2 started.
[   13.738542] hotplug: symlinking qca-nss0.bin to /lib/firmware/qca-nss0-retail.bin
[   13.819972] qca-nss 39000000.nss: NSS fw version: NSS.FW.12.1-022-CP.R
[   13.820016] qca-nss 39000000.nss: fw of size 859208 bytes copied to addr: 40000000, nss_id: 0
[   13.827386] ffffffc0790d3600: NSS core 0 DDR from 40000000 to 41000000
[   13.854467] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[   13.858604] nat46: module (version 4c5beee236841724219598fabb1edc93d4f08ce5) loaded.
[   13.861669] gre: GRE over IPv4 demultiplexor driver
[   13.862655] qca-nss 39000000.nss: NSS core 0 booted successfully
[   13.872067] ip_gre: GRE over IPv4 tunneling driver
[   13.881571] ip6_gre: GRE over IPv6 tunneling driver
[   13.889668] QCA multicast snooping installed successfully
[   13.926359] xt_FULLCONENAT: RFC3489 Full Cone NAT module
[   13.926359] xt_FULLCONENAT: Copyright (C) 2018 Chion Tang <[email protected]>
[   13.928378] nss_vlan_mgr_init_module[1940]:Module (Build Build Id: 07/23/24, 01:48:51) loaded
[   13.943861] PPP generic driver version 2.4.2
[   13.958117] NET: Registered PF_PPPOX protocol family
[   13.961820] PPTP driver version 0.8.5
[   13.975094] nss-macsec0 DT exist!
[   13.975272] nss-macsec1 DT exist!
[   13.977593] nss_macsec init success
[   13.985993] GACT probability on
[   13.987067] Mirror/redirect action on
[   13.996127] u32 classifier
[   13.996161]     input device check on
[   13.997747]     Actions configured
[   14.015330] Loading modules backported from Linux version v6.9.9-0-g28fdf4518483
[   14.015371] Backport generated by backports.git v6.1.97-1-29-gf1d24a3683b2
[   14.030706] l2tp_ppp: PPPoL2TP kernel driver, V2.0
[   14.060690] NET: Registered PF_QIPCRTR protocol family
[   14.063531] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information.
[   14.064775] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <[email protected]>. All Rights Reserved.
[   14.087303] xt_time: kernel timezone is -0000
[   14.130282] ath11k c000000.wifi: ipq6018 hw1.0
[   14.130318] ath11k c000000.wifi: FW memory mode: 1
[   14.166582] remoteproc remoteproc0: powering up cd00000.remoteproc
[   14.178336] remoteproc remoteproc0: Booting fw image IPQ6018/q6_fw.mdt, size 7340
[   14.910124] remoteproc remoteproc0: remote processor cd00000.remoteproc is now up
[   14.911620] ath11k c000000.wifi: chip_id 0x0 chip_family 0x4 board_id 0xff soc_id 0xffffffff
[   14.912972] kmodloader: done loading kernel modules from /etc/modules.d/*
[   14.916971] ath11k c000000.wifi: fw_version 0x25008f8e fw_build_timestamp 2024-03-01 03:54 fw_build_id WLAN.HK.2.5.0.1-03982-QCAHKSWPL_SILICONZ-3
[   14.953028] Unable to handle kernel read from unreadable memory at virtual address 0000000000000008
[   14.953072] Mem abort info:
[   14.960883]   ESR = 0x0000000096000005
[   14.963660]   EC = 0x25: DABT (current EL), IL = 32 bits
[   14.967481]   SET = 0, FnV = 0
[   14.972946]   EA = 0, S1PTW = 0
[   14.975810]   FSC = 0x05: level 1 translation fault
[   14.978852] Data abort info:
[   14.983710]   ISV = 0, ISS = 0x00000005, ISS2 = 0x00000000
[   14.986840]   CM = 0, WnR = 0, TnD = 0, TagAccess = 0
[   14.992134]   GCS = 0, Overlay = 0, DirtyBit = 0, Xs = 0
[   14.997257] user pgtable: 4k pages, 39-bit VAs, pgdp=0000000044be5000
[   15.002640] [0000000000000008] pgd=0000000000000000, p4d=0000000000000000, pud=0000000000000000
[   15.008982] Internal error: Oops: 0000000096000005 [#1] PREEMPT SMP
[   15.017479] Modules linked in: ath11k_ahb(O) ath11k(O) nf_flow_table_inet mac80211(O) ipt_REJECT cfg80211(O) xt_time xt_tcpudp xt_state xt_socket xt_recent xt_nat xt_multiport xt_mark xt_mac xt_limit xt_iprange xt_helper xt_conntrack xt_connmark xt_connlimit xt_connbytes xt_comment xt_TPROXY xt_TCPMSS xt_REDIRECT xt_MASQUERADE xt_LOG wireguard qrtr_smd qrtr qmi_helpers(O) ppp_async nft_reject_ipv6 nft_reject_ipv4 nft_reject_inet nft_reject nft_redir nft_quota nft_numgen nft_nat nft_masq nft_log nft_limit nft_hash nft_flow_offload nft_ct nft_compat nft_chain_nat nf_tproxy_ipv6 nf_tproxy_ipv4 nf_tables nf_socket_ipv6 nf_socket_ipv4 nf_reject_ipv4 nf_log_syslog nf_flow_table nf_conntrack_netlink nf_conncount libcrc32c libchacha20poly1305 l2tp_ppp iptable_nat iptable_mangle iptable_filter ip_tables hwmon crc_ccitt compat(O) sch_tbf sch_ingress sch_htb sch_hfsc em_u32 cls_u32 cls_route cls_matchall cls_fw cls_flow cls_basic act_skbedit act_mirred act_gact qca_nss_tunipip6(O) qca_nss_tun6rd(O) qca_nss_macsec(O)
[   15.017684]  qca_nss_vxlanmgr(O) qca_nss_pptp(O) pptp qca_nss_pppoe(O) pppoe pppox qca_nss_map_t(O) qca_nss_lag_mgr(O) qca_nss_l2tpv2(O) ppp_generic slhc qca_nss_gre(O) qca_nss_bridge_mgr(O) qca_nss_vlan(O) xt_FULLCONENAT(O) nf_nat nf_conntrack nf_defrag_ipv4 xt_set ip_set_list_set ip_set_hash_netportnet ip_set_hash_netport ip_set_hash_netnet ip_set_hash_netiface ip_set_hash_net ip_set_hash_mac ip_set_hash_ipportnet ip_set_hash_ipportip ip_set_hash_ipport ip_set_hash_ipmark ip_set_hash_ipmac ip_set_hash_ip ip_set_bitmap_port ip_set_bitmap_ipmac ip_set_bitmap_ip ip_set nfnetlink ip6table_mangle ip6table_filter ip6_tables ip6t_REJECT x_tables nf_reject_ipv6 qca_mcs(O) bonding ip6_gre ip_gre gre ifb nat46(O) nf_defrag_ipv6 sit qca_nss_drv(O) ip6_tunnel tunnel6 tunnel4 tun raid10 raid1 raid0 md_mod vxlan seqiv michael_mic geniv leds_gpio xhci_plat_hcd xhci_pci xhci_hcd dwc3 dwc3_qcom qca_nss_dp(O) qca_ssdk(O) gpio_button_hotplug(O) f2fs ext4 mbcache jbd2 crc32c_generic crc32_generic
[   15.177276] CPU: 3 PID: 169 Comm: kworker/u8:3 Tainted: G           O       6.6.41 #0
[   15.199514] Hardware name: JDCloud AX1800 Pro (DT)
[   15.207322] Workqueue: ath11k_qmi_driver_event ath11k_qmi_deinit_service [ath11k]
[   15.212014] pstate: 40400005 (nZcv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[   15.219564] pc : ath11k_dbring_buf_cleanup+0xbec/0x1014 [ath11k]
[   15.226334] lr : ath11k_wmi_cmd_init+0x64/0x55c [ath11k]
[   15.232581] sp : ffffffc081713b40
[   15.237873] x29: ffffffc081713b40 x28: dead000000000122 x27: ffffff8009de0000
[   15.241091] x26: ffffff8009de0168 x25: dead000000000100 x24: ffffff8009df0000
[   15.248210] x23: ffffff8009de0018 x22: ffffff8009de1068 x21: ffffff8009debf28
[   15.255328] x20: ffffff8009de0000 x19: ffffff8009de0000 x18: 0000000000005cf0
[   15.262445] x17: 00000000000014b0 x16: 0000000000001498 x15: 0000000000005ef8
[   15.269564] x14: 0000000000001478 x13: 0000000000001458 x12: 0000000000000001
[   15.276681] x11: 0000000000000000 x10: 0000000000000002 x9 : 0000000000000000
[   15.283799] x8 : ffffffc081713cd0 x7 : 0000000000000000 x6 : 000000000000003f
[   15.290918] x5 : 0000000000000000 x4 : 0000000000000002 x3 : ffffff8009df0000
[   15.298036] x2 : 0000000000000008 x1 : ffffffc081713bc4 x0 : ffffff8009de0000
[   15.305156] Call trace:
[   15.312263]  ath11k_dbring_buf_cleanup+0xbec/0x1014 [ath11k]
[   15.314527]  ath11k_core_qmi_firmware_ready+0x190/0x5b0 [ath11k]
[   15.320429]  ath11k_qmi_deinit_service+0x1380/0x194c [ath11k]
[   15.326419]  process_one_work+0x160/0x280
[   15.332058]  worker_thread+0x31c/0x44c
[   15.336051]  kthread+0x10c/0x110
[   15.339696]  ret_from_fork+0x10/0x20
[   15.343086] Code: b949e402 b9506004 f9614465 d37df042 (b86268a2)
[   15.346647] ---[ end trace 0000000000000000 ]---
[   15.352635] Kernel panic - not syncing: Oops: Fatal exception
[   15.357322] SMP: stopping secondary CPUs
[   15.362967] Kernel Offset: disabled
[   15.366952] CPU features: 0x0,00000000,10000000,0000400b
[   15.370169] Memory Limit: none
[   15.975748] Rebooting in 1 seconds..

Recommend Projects

  • React photo React

    A declarative, efficient, and flexible JavaScript library for building user interfaces.

  • Vue.js photo Vue.js

    🖖 Vue.js is a progressive, incrementally-adoptable JavaScript framework for building UI on the web.

  • Typescript photo Typescript

    TypeScript is a superset of JavaScript that compiles to clean JavaScript output.

  • TensorFlow photo TensorFlow

    An Open Source Machine Learning Framework for Everyone

  • Django photo Django

    The Web framework for perfectionists with deadlines.

  • D3 photo D3

    Bring data to life with SVG, Canvas and HTML. 📊📈🎉

Recommend Topics

  • javascript

    JavaScript (JS) is a lightweight interpreted programming language with first-class functions.

  • web

    Some thing interesting about web. New door for the world.

  • server

    A server is a program made to process requests and deliver data to clients.

  • Machine learning

    Machine learning is a way of modeling and interpreting data that allows a piece of software to respond intelligently.

  • Game

    Some thing interesting about game, make everyone happy.

Recommend Org

  • Facebook photo Facebook

    We are working to build community through open source technology. NB: members must have two-factor auth.

  • Microsoft photo Microsoft

    Open source projects and samples from Microsoft.

  • Google photo Google

    Google ❤️ Open Source for everyone.

  • D3 photo D3

    Data-Driven Documents codes.