vitorgamer58 / brazostweaker Goto Github PK

What steps will reproduce the problem?

1. Install BrazosTweaker v1.0.7 on WHS 2011, running on Sapphire motherboard

2. Followed instructions to set voltages for P0,P1 and P2 states

3. Used OCCT to test and CPU-Z/HW Monitor to check voltages

What is the expected output? What do you see instead?

-CPU-Z, OCCT, HW Monitor should show 1.25v for CPU, instead shows the default 
1.3v


What version of the product are you using? On what operating system?

-BrazosTweaker v1.0.7 64 bit on WHS 2011

Please provide any additional information below.

Setting a really low voltage for the P0 or P2 state will crash the system after 
a load test. So the voltages appear to be working BUT setting the voltage to 
1.25v for example, will not work. And there's no change in the Watt Meter 
reading 

What steps will reproduce the problem?
1. I did some undervolt testing and when I tried to save the new values in the 
service part of the application this error popped up and now it shows every 
time I click on the service button (details and screenshot are posted on 
pastebin at the bottom)

What is the expected output? What do you see instead?
Open the service dialog and configure it. I see the error message, on continue 
the application doesn't close but it doesn't open the service dialog either.

What version of the product are you using? On what operating system?
V1.0.6, Windows 7 32, AMD E-350 (HP dm1z-3200 series netbook)

Please provide any additional information below.
Reinstalling or rebooting did not solve the porblem.

http://pastebin.com/mzjJnNhR

C-60 has 3 actual P states ( unlike the C-50 which only has 2) The fastest is 
P0 which is 1.3 ghz (known as turbo mode), then theres P1 which is 1ghz which 
is supposed to be its normal speed, and finally p2 which is 800Mhz which is its 
resting/idle speed.

Before i applied my VID changes i kept your program on the top and ran thru 
various scenarios and saw that the power state ( in hogh performance mode) 
varied between P0 P1 P2 depending on what i was doing. It would go to p0 for a 
few seconds then p1 and back to p2 when it was idle.

I changed the VID from 1.1250 to 1.1 to undervolt it like i did with the c-50 i 
previously had. Then i applied the settings.

Now the P state just varies from P0 to P1. It doesnt go to the idle state of P2 
anymore.

What steps will reproduce the problem?
1. Changing any settings and applying them


What is the expected output? What do you see instead?
I expected it to vary between the 3 states like it did initially instead of 
staying in p0 and p1

What version of the product are you using? On what operating system?
Windows 7 64 bit , Brazos 1.0.4

Please provide any additional information below.
As a side note it seems i am able to overclock this thing ! On lowering the 
multiplier in P0 from 3.0 to 2.5 CPU-Z reports a processor speed of 1.6ghz. I 
will attach a  screen shot of cpuz with brazos and prime 95 running to show the 
overclock.

I don't see any mention in the documentation or user guides about C-70 support, 
and the latest version of this program was released nearly a year ago (January; 
it's now December). 

Before trying this on a system with a C-70 (some new Acer netbooks), I am 
wondering if the creators of the software condone its use on this chip. 

Anyone tried this with a C-70 yet?

Not a problem, but question.

Does this work with AMD e-300 processors?

How easy is it to use this problem?

What is the recommended voltage for AMD e-300, for someone who has never done 
this sort of thing before?

What steps will reproduce the problem?
1.double click on brazostweaker 
2.starts to load 
3.brazostweaker has stopped working 

brazostweaker not booting


windows 7 64-bit brazostweaker V1.0.7

Please provide any additional information below.

i downloaded NET framework as well still nothing 

the laptop im using is an asus x53u  with AMD brazos dualcore c60 CPU 6GB ddr3 
ram 320GB HDD  Windows 7 home premium    

Any help would be appreciated 
                                 thanks

What steps will reproduce the problem?
1. Change Voltage to recommended Values in User Guide
2. Use balanced power scheme (unmodified)
3. Start Orthos, CPU-Z

What is the expected output? What do you see instead?
I never see the asterisk mentioned in User Guide, Orthos shows
1645 Mhz, CPU-Z either, multiplier 16,5 implies P0 State

What version of the product are you using? On what operating system?
V1.07 on windows 7 Home 32bit

Please provide any additional information below.

Not an actual issue but would be cool to see this nice tool ported to linux

best regards and keep up the great work

Hi,

i'm trying to desintall BrazosTweaker 1.0.4 but I have this message :
"There is a problem with this Windows Installer package. A program run as part 
of the setup did not finish as expected"
I need the BrazosTweaker_x64_Setup V1.0.4.msi file to repair my installation 
but I can't find it.

Could you please help my with that.
Thank a lot for your time.

Hy im Dante and i own a MSI e350DM -e33 can you tell me how to overcloc with 
the brazors tweaker or how tom mod mi bios because it dosen't hav a cpu fsb 
changer Thanks

Hi Guys,

is it possible to integrate a Fan Control Software in BrazosTweaker for an 
Toshiba NB550D-105?
I'd like to stop the fan until 70°C. With SpeedFan it will not work!

Thanks Max

What steps will reproduce the problem?
1. increase font size from default which is common on a HTPC for distance 
viewing

What is the expected output? What do you see instead?

Most of the status widgets at the top are cut off and the other elements 
(voltage/multiplier) below don't flow even when the window is resized


What version of the product are you using? On what operating system?
latest release on Windows 7


Please provide any additional information below.

I understand this a windows driver issue but can you some fix it with this 
service?  The processor stuck in P0 regardless of Power Scheme (max battery or 
balance or always on).  I tried all scheme already.

What steps will reproduce the problem?
1. Changing the voltage on NB P0 or NB P1

What is the expected output? 
Voltage should be applied.

What do you see instead?
Exception will be thrown, that P2 VID is higher than P1 VID.

What steps will reproduce the problem?
1. Change Service thresholds to 10 and 1 for p state scaling
2. Try to enter service config again
3. Crash -- no way around this ever again, even after uninstall.

What is the expected output? What do you see instead?
It's supposed to open or at least handle the exception. Instead, I see this: 
http://img525.imageshack.us/img525/3613/crapxc.png

What version of the product are you using? On what operating system?
1.0.7 Win7 x32 C-60 Acer W500

Please provide any additional information below.
Even uninstalling, clearing registry within the settings, etc doesn't work. 
Maybe I'll try to scour things by hand...

What steps will reproduce the problem?
1. Activating Custom Cool&Quite

404. That’s an error.

The requested URL /files/BrazosTweaker%2520x64%2520Setup%2520V1.0.6.msi was not 
found on this server. That’s all we know.

Temp/Fan on Hewlett-Packard/3577 not supported yet. what is it tryen to say?

Hello!

Hope you can help us with a new version of brazostweaker!

I have an Asus 1225B and I didn't find ANY PROGRAM on the internet to overclock 
a little bit my pc, your software included! 
It says "Temp/Fan on American Megatrends Inc./1225B not supported yet."

I have an upgraded BIOS and I really need help for my AMD Brazos APU!

AMD E-450 APU with Radeon(tm) HD Graphics 1.65Ghz

Windows 7 Home Edition 64 bits

Sorry my bad English, hug from Portugal!

Unable to clock the C-50 in any way, up or down.

What steps will reproduce the problem?
1. trying to open BroazosTweaker
2. re-installing and trying again
3.

What is the expected output? What do you see instead?
I want the program to open I get a exception message.

What version of the product are you using? On what operating system?
v1.0.7 I am using an amd e-350 processor and amd radeon hd 6130 graphics card. 

Please provide any additional information below.

This is what the message says:

WinRing0 could not be initialized.Make sure to use the right release for your 
system: x64 at BrazosTweaker.Program.Main()

I wonder if you're working to get support for 1215b with E450, which would be 
appreciated ^^

What steps will reproduce the problem?

There are two powerstates for NB/GPU. 450 MHz at high demand and 342 MHz at low 
demand.

BazosTweak does not refer to these correctly. Whatever the actual powerstate 
is, the set voltage is always in NBP0. If you find and set a voltage stable at 
low demand, your system will freeze at high demand.
Whatever you set in NBP1, it is ignored; you can set 0.1 V without freeze.


What is the expected output? What do you see instead?
There are two NB/GPU voltages that you can set, NBP0 and NBP1. One should refer 
to high GPU demand, and the another should refer to low GPU demand.

What version of the product are you using? On what operating system?
BrazosTweaker V1.0.6, W7 starter 32
Hardware: AMD C-30 (Toshiba NB550D) 

Please provide any additional information below.

The software is cool! Looking forward for further development. A fan control 
would be awesome. Also some registry tool, so that you don't need to set the 
voltages after every reset/resume. But already an achievement, congratulation!

What steps will reproduce the problem?
1. Apply a change to voltage.

What is the expected output? What do you see instead?
PState and frequency should be unaffected.

What version of the product are you using? On what operating system?
1.0.7
Windows 7 x64

Please provide any additional information below.
When I hit apply after adjusting a voltage, the reported PState on both cores 
drops to "P3" and 444MHz. Changing the Power Plan resets the cores back to a 
valid PState.

Also, when attempting to calibrate P0, the cores constantly bounce between P0 
and P1, even with a minimum processor speed of 100%

Thanks!

My issue is similar to #11, but a bit different. Here it is:

1) Initial settings:
- Brazos runs on Acer tablet W500, cpu C-50, windows 7/8
- Initial voltage is 1.1 for P0 and and 0.975 for P1/2.
- With Brazos setting on first boot, P0 can be as low as 0.9 and P0/P1 are 
0.825 running all Wprime/ Intel burn test without any issue 

2) Tablet is set to sleep, hibernation or video shutdown during usage :
- usually after 1 day, problem starts to be like this: there are very 
thin,black/gray horizontal lines of flickering-like happen randomly on screen 
nonstop or maybe once per few mins.
- Simply restart will fix it, but will happen again after 
sleep/hibernation/screen turn off
- Re-adjust voltage of : PO= 0.9875 and P1/2 = 0.975 will fix it but then 0.975 
is no undervoltage for P1/2 at all.

3)So problem could be too low, incorrect voltage at P1/2 ? but it works fine on 
first start or after reboot or could be something with sleep/hibernation 
against Brazo service ?

Note: about the flickering lines , you need to have sharp eyes to see it and on 
white background/website. And the longer you let the system run ( no restart ) 
it will happen more often.

CPU VID/Mult is working fine.

NB VID has no effect. I can apply it, but temp is not changing. Lowering to is 
0,0125V is possible. 
NB Mult reverts back to original settings if i press "Apply".

- BrazosTweaker V1.0.7 amd64
- Win7 SP1 64bit
- Foxconn nT-A3500 Bios B11F1P03

Using windows, leaving the case open and the system in idle state, the fan 
stops for a few seconds, then it runs, stops, runs and so on. CPU/NB-Temps are 
around 50°C.

On linux i got complaints about broken ACPI-Tables. Also the fan is permanently 
blowing (cold air) while the cpu throttles down.

What steps will reproduce the problem?
1. put the system to standby 
2. wake up from standby

What is the expected output? What do you see instead?
System should go to and come back from standby without problems.
Instead, it comes back shortly and then freezes (with a forced reboot) after 
only a few (1-3) seconds.

What version of the product are you using? On what operating system?
1.0.7 on Windows 7 64bit


Please provide any additional information below.
I'm not 100% sure that BrazosTweaker is the source of the problem.

What steps will reproduce the problem?
1. Temperature is not going lower after underclocking and undervolting(same as 
battery working time, still same)
2. It says "Temp/Fan on American Megatrends Inc./RV415/RV415 not supported yet."
3. Performance is not better after oveclocking

What is the expected output? What do you see instead?
I want to have more time working on battery and some more power in games

What version of the product are you using? On what operating system?
Version is 1.0.7 64b on Win7 Home Premium 64bit

Please provide any additional information below.
System freezes with lower voltage than 0.75V witch 825MHz clock
Sorry for my English

What steps will reproduce the problem?
1. Possible to add profiles (like K10Stat)?

What is the expected output? What do you see instead?



What version of the product are you using? On what operating system?


Please provide any additional information below.

I would like to request a feature, to add multiple profiles, at minimum two. 
One for low power, another for performance, similar to how K10Stat offers 5 
configurable profiles. Thanks.

i need the default settings for the high performance tab in the sevice section.
i lost the defaukts sorry 

On my Asus E35M1-I changing the VID for the northbridge has no effect. I can 
even lower it to 0,0125 and it still doesn't lock up. Of course, power 
consumption does not change either.

CPU VID changes work fine, though.

> What version of the product are you using? On what operating system?
v1.05 on Windows Server 2003 (x86)

What steps will reproduce the problem?
1. high clock without damage the computer (x40) PO P1
2. faster streaming you tube
3. games become nice without bug

Don´t I  know if I did it correct?

AMD C_50

I have tried the Tweaker on my Lenovo x121e laptop with a E-350 on it. I set 
the multiplier-divider to 1.0 which I know is dumb but I just wanted to see 
whether the tweaker works. Then the laptop froze. 

When restarting the laptop will not boot with the hdd installed. Now my 
question is whether I can brick a SATA controller by setting an dumb value in 
the tweaker?

AMD E-350 zacate / Radeon HD 6310 -> Would it be possible to add support for 
those two. I am interested more in overclocking, and there are no tools that 
allows any OC on those two...

Acer AO725

APU: C70
Modo: ZA10_BZ

In NB states I can change the VID but CAN'T alter the Mult, it is restored at 
default value every time I press apply. Already tried to disable PowerPlay.

where can i see the changelog?

What steps will reproduce the problem?
1. i have enabled custom cool'n and quiet
2. i have already this message on brazos tweaker
3. someboby known an issue?
please share great thanks all people and continue :)

What steps will reproduce the problem?
1. Set P2 divisor higher than 4.25
2.
3.

What is the expected output? What do you see instead?

I expect Windows to scale frequencies as usual.
However it just gets stuck in the frequency set at P2. If I set the divisor to 
4.25 or 4.0 then windows start scaling up to P0 again.

What version of the product are you using? On what operating system?

brazos tweaker v1.0.7
windows 7 64bit home premium

Please provide any additional information below.

apu is on a hp dm1-4100.

What steps will reproduce the problem?
windows 7, you have to set display text size to medium (125%)
1. Open "Personalize" menu via right mouse press on a desktop. 
2. Press "Display" sub-menu in "see also" section.
3. Select "medium - 125 %" and log off.
4. Start brazos tweak app 1.0.7 and observe a graphical issue. 

https://www.dropbox.com/s/j6oqttbfjzz65r5/brazosIssue.jpg

What steps will reproduce the problem?
1.
2.
3.

What is the expected output? What do you see instead?
I use CPU-Z too, and the CPU paramethers  doesn't agree. Plase check my attach 
file.

What version of the product are you using? On what operating system?
Win7

Please provide any additional information below.
Maybe I make some mistake, but i dont understand what is the problem, why cant 
I overclock my e450?

What steps will reproduce the problem?
Launching the Installer.

What is the expected output? What do you see instead?
Windows 8 RTM includes the .NET Runtime 4.5. That reléase isn't recognized by 
the installer. The installer, wrongly, asks me to download the .NET runtime 
2.0, while .NET 4.5 is already installed.

The expected output is a successful installation, since the .NET runtimes are 
already installed.

What version of the product are you using? On what operating system?
The latest, 1.07

Please provide any additional information below.
This happens with the Windows 8 RTM Dev Preview.

What steps will reproduce the problem?
1. -
2. -
3. -

What is the expected output? What do you see instead?
-Increase frequency but no respond

What version of the product are you using? On what operating system?
-Version 1.07

Please provide any additional information below.
-It says that " Insyde Corp./JE40_BZ not supported yet." which motherboard in 
Acer Aspire 4253

Hello,

I recently installed Brazos Tweaker on my MSI U270 with AMD E-350 APU in order 
to undervolt the sytem and gain battery life. I found different settings people 
use, but they are all faulty. They were about:

P0: 1,1500-1,1625
P1: 0,9875-1,0250
P2: 0,8000-0,8375
NB P0: 0,8500
NB P1: 0,8000

Such settings, or settings that are "working for most of the users", don't work 
there. Even now, with setting: P0: 1,2000; P1: 1,1000; P2: 0,9000; NB P0: 
0,9000; NB P1: 0,8500; I receive BSODs and dead freezes when on maximum load.

While I can partly understand that, cause every processor is different and will 
or will not work on some voltage, I get very dissappointed by the application 
itself. When I set everyting up, apply the settings, set them permanent, and 
succesfully restart the computer, everything works fine. My battery life is far 
better, and it goes up from 4 hours to even 6 hours. But after I put the 
computer to sleep (and later it hibernates) all gets messed up. Brazos Tweaker 
still says the settings are active, and the built-in monitoring confirms it, 
the battery indicator shows no more that 3 hours, and percents are going down 
in my eyes. And if I would like to put the settings back to life, and get my 5 
hours back, I have to take out the battery for a few seconds, nothing else 
helps. Yesterday I turned off the hibernation, but still no luck, app reacts 
the same.

Is there any solution to this?

PS. I would like to propose a little change if possible - the settings could be 
pinned to an energy plan. For example the undervolting would be applied to 
Battery Save mode, and if you turn into Normal or Top Performance mode, normal 
voltage settings would apply. That would help browsing and MS Office'ing on 
sligthly lower than should be voltage, and on other energy plans, top 
performancing won't end up with a BSOD or a freeze. At least I think so...

Best Regards,
Mike