Comments (10)
Thats indeed the tough part, finding a suitable container.
But here is the trick, put the sled into hot water ~140°F where it gets soft, then push it gently into the sled. Repeat it if necessary, you will squeeze it until it fits.
Not perfect but works!
-Sam
from ispindel.
The sled is slightly too large for the Ebay container that I bought; image shows how far it goes before it jams. Should be able to mod it slightly by filing off some material.
XXLBIG PET Micro Geocaching container geocache Petling preform Soda bottle FTF
http://www.ebay.com/itm/142295113730?_trksid=p2060353.m2749.l2649&ssPageName=STRK%3AMEBIDX%3AIT
https://raw.githubusercontent.com/universam1/iSpindel/master/drawer/drawer-combo-short.stl
from ispindel.
So based on the above comments this is the only one that should remain in that directory:
https://raw.githubusercontent.com/universam1/iSpindel/master/drawer/drawer-combo-short.stl
and the other ones should be deleted? Is that correct @universam1 ?
from ispindel.
Yeah I know, maybe I should describe the dimensions. Actually since there suppliers PET preform changed its dimensions over the last months, I just left the different sizes there...
I will add dimensions so one could find a fitting sled.
from ispindel.
I tried the hot water trick, put water in a ceramic dish, floated the sled on the water and put it in the microwave on the beverage setting and it worked well to soften up the material so it could fit the tube, however the sled legs splayed out a little (warped) so flipped it over and pressed it back into shape and that seems to have fixed that issue. I'll find out when I get the circuit board but shouldn't be too difficult to reform it.
I think keep the different drawer designs but just add more info on which containers/configurations they fit.
from ispindel.
@universam1 any idea what design matches this one:
http://www.ebay.com/itm/132118452191
from ispindel.
I've added the length of the different designs. So one might check which of these do fit to his preform. Still you can squeeze that PLA quite easily with hot air or water if necessary.
from ispindel.
Is that outer or inner dimensions?
If I measure my container I get:
- Inner:
- Width: 33.3mm
- Height: 129.6mm
- Outer:
- Width-Top-By-Opening: 36mm
- Width-Middle-Of-Height: 39.2mm
- Height: 133mm
So I'm not sure which one to pick here:
- drawer-36x133-thing2231986.stl (leaning towards this one)
- drawer-38x133.stl
Maybe a README.md with where to measure would be a nice addition. I don't have a 3D-printer myself so I hope to avoid an extra print-request from my 3D-printing-contact.
from ispindel.
It is the outer dia of the sled hence the inner of the container.
Your container is quite a bit thinner, I guess you have to hack it a lot, it might be really super tight if possible at all.
from ispindel.
Hi @dsvensson
Were you able to fit a drawer to your 33x130 tube and made it work? I am having difficulties with a quite smaller tube.
from ispindel.
Related Issues (20)
- iSpindel HOT 2
- Doc link do not exist: https://www.ispindel.de/docs/tools/TestServer/Readme.md HOT 4
- Is it possible to reduce the accuracy of "battery" and keep 2-3 digits after the decimal point? HOT 10
- Wemos V4 HOT 10
- Proposition: Have a project able to route the messages HOT 3
- Discussion: What about using a ispindel github org (e.g.: https://github.com/ispindel, ...) ? HOT 5
- Issue with Ubidots API HOT 3
- Create new release :tada: HOT 3
- Firmware 7.2.0 identifies itself as 7.1.4 HOT 2
- History of tilt entity in HA not shown as line graph HOT 5
- Same issue as Issue #571 - Issue with Ubidots API HOT 2
- HTTP404 when clicking "Delete WiFi configuration and reboot" /r HOT 7
- Wrong tilt value HOT 4
- Holder for the PCB card in the container HOT 15
- Changes in ArduinoJson broke Sender.cpp HOT 1
- MQTT topic to force iSpindel in configuration (AP) mode? HOT 6
- Exception (28) on plain modules HOT 2
- SSL support for MQTT HOT 2
- Biradefteri HOT 1
- If gyro sensor is mounted inverted, the offset calibration does something that makes the unit not read less than 60 degrees when orientated vertically HOT 2
Recommend Projects
-
React
A declarative, efficient, and flexible JavaScript library for building user interfaces.
-
Vue.js
🖖 Vue.js is a progressive, incrementally-adoptable JavaScript framework for building UI on the web.
-
Typescript
TypeScript is a superset of JavaScript that compiles to clean JavaScript output.
-
TensorFlow
An Open Source Machine Learning Framework for Everyone
-
Django
The Web framework for perfectionists with deadlines.
-
Laravel
A PHP framework for web artisans
-
D3
Bring data to life with SVG, Canvas and HTML. 📊📈🎉
-
Recommend Topics
-
javascript
JavaScript (JS) is a lightweight interpreted programming language with first-class functions.
-
web
Some thing interesting about web. New door for the world.
-
server
A server is a program made to process requests and deliver data to clients.
-
Machine learning
Machine learning is a way of modeling and interpreting data that allows a piece of software to respond intelligently.
-
Visualization
Some thing interesting about visualization, use data art
-
Game
Some thing interesting about game, make everyone happy.
Recommend Org
-
Facebook
We are working to build community through open source technology. NB: members must have two-factor auth.
-
Microsoft
Open source projects and samples from Microsoft.
-
Google
Google ❤️ Open Source for everyone.
-
Alibaba
Alibaba Open Source for everyone
-
D3
Data-Driven Documents codes.
-
Tencent
China tencent open source team.
from ispindel.