Comments (9)
The oven fan is controlled by default. If you want to make the device silent if not warm, you can apply the mod described in this wiki page
from t-962-improvements.
@jieter
Thanks for your answer.
Just upgraded FW ;-)
I just realized that FAN control is not for the big fan on rear during reflow but the little noisy one to refresh PCB. Sounds good using DS18B20 also to detect and activate this one ;-)
Just for information, you don't need to unground n_ISP to upgrade firmware (at least on my T962), this mean that simplify FW upgrade with a FTDI:
Just wire n_ISP to ground and connect DTR of any FTDI 3V3 USB to nRESET and start upgrade, that should be straightforward. Of course after flash, unwire n_ISP
Next step, basic FET transistor mode for FAN, got some BS270, simplest way, cut the GND wire (the dot dot dot one, not the dot line dot) of the fan. Then connect drain and source and then gate direct onto PCB (well it should have been like this)
Unfortunately I cut the wire too short, needed to solder 3rd on the FET gate, may be too long day, anyway, final wiring as follow:
Everything sounds good, may be a test fan connected to this AD0 output on firmware would be great so see if everything is well connected ;-)
Really thank for this marvelous firmware, amazing and let so much space on target that would allow much more mods !!!!
from t-962-improvements.
Just a note on the system fan testing issue: The firmware will turn that fan on briefly during boot which makes modification verification simple
from t-962-improvements.
According to the DS18B20 datasheet, a FET is needed in the parasite power mode. Why is there not a FET in your design?
from t-962-improvements.
from t-962-improvements.
Thanks for the clarification, Werner! My T-962 will arrive tomorrow. I cannot wait to try the mod out.
from t-962-improvements.
from t-962-improvements.
@southern-boy, because a thermocouple requires that the cold junction temperature be measured, so it can be compensated for, and that is what the one wire sensor is providing. This is what the oven is missing from the factory, which causes the oven temperature to drift, as the cold junction temperature changes. A thermocouple measures the difference between the thermocouple junctions. One of the junctions is in the oven, and the second one is the cold junction that is formed where the thermocouple is attached to the PCB (every set of dissimilar metals is considered a thermocouple junction). If the temperature of the cold junction is known, and never changes, then technically you wouldn't need to measure it. Alas, this is not the case, and the electronics chamber where the cold junction is located, heats up as the oven is used.
Now, if instead you use the 4 channel thermocouple interface board, it has the cold junction compensation built in, so in that case the DS18B20 is not required. This is the route I took when modifying my oven, and it does indeed work very well.
from t-962-improvements.
from t-962-improvements.
Related Issues (20)
- For Setup/Calibrations OFFSET Parameter for Left and Right TCs are Too Course HOT 2
- Flat Ribbon Cable Adapter
- I made a OpenOffice Calc sheet to help generate custom reflow profiles HOT 5
- The source codes are posted HOT 31
- [WiP] ESPHome component
- T-962A Screen blank after flashing new firmware HOT 14
- New version T962 HOT 1
- Calibration with MAX31850K connected HOT 1
- Raspberry Pi Serial Connection for flashing and Web GUI
- Just reporting: 2023 T962 - Upgrade successful HOT 1
- Timer does not start HOT 15
- quite original (Elektor-modified) T962 has significant temperature difference, solder not melting HOT 44
- Instructions for flashing seem to be wrong? HOT 5
- Why not trying slowly moving the board instead of improving heat distribution ? HOT 1
- Heater and Fun runs togheter? HOT 2
- T-962 V2.0 ? HOT 1
- Seeking Copy of T-962a+ Firmware HOT 3
- T-962 parts? HOT 6
- Adafruit Max3150K is not gettting recognized by the firmware HOT 1
- Is this firmware suitable for T-962 version 2.0+photo HOT 2
Recommend Projects
-
React
A declarative, efficient, and flexible JavaScript library for building user interfaces.
-
Vue.js
🖖 Vue.js is a progressive, incrementally-adoptable JavaScript framework for building UI on the web.
-
Typescript
TypeScript is a superset of JavaScript that compiles to clean JavaScript output.
-
TensorFlow
An Open Source Machine Learning Framework for Everyone
-
Django
The Web framework for perfectionists with deadlines.
-
Laravel
A PHP framework for web artisans
-
D3
Bring data to life with SVG, Canvas and HTML. 📊📈🎉
-
Recommend Topics
-
javascript
JavaScript (JS) is a lightweight interpreted programming language with first-class functions.
-
web
Some thing interesting about web. New door for the world.
-
server
A server is a program made to process requests and deliver data to clients.
-
Machine learning
Machine learning is a way of modeling and interpreting data that allows a piece of software to respond intelligently.
-
Visualization
Some thing interesting about visualization, use data art
-
Game
Some thing interesting about game, make everyone happy.
Recommend Org
-
Facebook
We are working to build community through open source technology. NB: members must have two-factor auth.
-
Microsoft
Open source projects and samples from Microsoft.
-
Google
Google ❤️ Open Source for everyone.
-
Alibaba
Alibaba Open Source for everyone
-
D3
Data-Driven Documents codes.
-
Tencent
China tencent open source team.
from t-962-improvements.