Comments (5)
There is a similar project... Can be sent immediately via uart
Reflow profile calculator.zip
from t-962-improvements.
The problem with this approach to developing Reflow Profiles, is that the profiles are just guides or starting points for making adjustments required that match the intended PCB and its associated SMD components, with the particular solder paste being used. The solder paste Manufacturers have their own reflow profile recommendations, while Component Manufacturers also have suggested reflow profiles. So, finding a sweet spot usually requires some tweaking of the Reflow Profile. Unfortunately, the current firmware does not provide an easy way to make fine adjustments to the reflow profiles.
I have developed a spreadsheet that generates a reflow profile based on separate input parameters for the various phases (e.g., Preheat, Soak, Reflow, Cooldown) of the reflow profile. Here's a screen shot of the input parameters and resulting chart (Reflow Profile).
The spreadsheet also generates a Time/Temperature table in 10 second intervals up to 470 seconds.
I'm not going to provide copies of my spreadsheet, but do plan to code this implementation, and then submit a Pull Request that implements this parameter based approach in firmware.
This will modify the firmware so that it can generate all Reflow Profiles based on the same input parameters as my spreadsheet, for either firmware Stored Profiles, or Custom Profiles, That way the user can select from those provided profiles and make parameter adjustments, as necessary. Similar to current profile features, the user should be able to save Custom Profiles to the oven's EEPROM.
Using my spreadsheet, I was able to reconstruct the built-in reflow profiles using the same list of parameters.
For comparison, here are the plots for parameter based (upper chart), and plot of the source code time/temperature data (lower chart).
AmTech 4300 ------------------------------------------------------------
AmTech NC-31 ----------------------------------------------------------
AmTech Syntech Lead Free ----------------------------------------------------------
Ramp Speed Test ----------------------------------------------------------------
PID Control Test ----------------------------------------------------------------------
from t-962-improvements.
Unfortunately, the problem of these stoves is not in profiles and firmware... Without a complete replacement of heaters and the addition of a convention, they do not work normally on the profile... There are two main problems are the low heating rate (not dependent on the graph) and not the uniformity of heating... In the first case, it is decided to replace the heaters in the second by adding a convention fan.
from t-962-improvements.
https://budgetlightforum.com/node/66551
from t-962-improvements.
from t-962-improvements.
Related Issues (20)
- Add Safety Waring to Firmware Instructions. HOT 1
- "COLD JUNCTION NOT PRESENT" DS18S20 not available from DigiKey; DS18S20+PAR substituted HOT 5
- For Setup/Calibrations OFFSET Parameter for Left and Right TCs are Too Course HOT 2
- Flat Ribbon Cable Adapter
- The source codes are posted HOT 31
- [WiP] ESPHome component
- T-962A Screen blank after flashing new firmware HOT 14
- New version T962 HOT 1
- Calibration with MAX31850K connected HOT 1
- Raspberry Pi Serial Connection for flashing and Web GUI
- Just reporting: 2023 T962 - Upgrade successful HOT 1
- Timer does not start HOT 15
- quite original (Elektor-modified) T962 has significant temperature difference, solder not melting HOT 44
- Instructions for flashing seem to be wrong? HOT 5
- Why not trying slowly moving the board instead of improving heat distribution ? HOT 1
- Heater and Fun runs togheter? HOT 2
- T-962 V2.0 ? HOT 1
- Seeking Copy of T-962a+ Firmware HOT 3
- T-962 parts? HOT 6
Recommend Projects
-
React
A declarative, efficient, and flexible JavaScript library for building user interfaces.
-
Vue.js
🖖 Vue.js is a progressive, incrementally-adoptable JavaScript framework for building UI on the web.
-
Typescript
TypeScript is a superset of JavaScript that compiles to clean JavaScript output.
-
TensorFlow
An Open Source Machine Learning Framework for Everyone
-
Django
The Web framework for perfectionists with deadlines.
-
Laravel
A PHP framework for web artisans
-
D3
Bring data to life with SVG, Canvas and HTML. 📊📈🎉
-
Recommend Topics
-
javascript
JavaScript (JS) is a lightweight interpreted programming language with first-class functions.
-
web
Some thing interesting about web. New door for the world.
-
server
A server is a program made to process requests and deliver data to clients.
-
Machine learning
Machine learning is a way of modeling and interpreting data that allows a piece of software to respond intelligently.
-
Visualization
Some thing interesting about visualization, use data art
-
Game
Some thing interesting about game, make everyone happy.
Recommend Org
-
Facebook
We are working to build community through open source technology. NB: members must have two-factor auth.
-
Microsoft
Open source projects and samples from Microsoft.
-
Google
Google ❤️ Open Source for everyone.
-
Alibaba
Alibaba Open Source for everyone
-
D3
Data-Driven Documents codes.
-
Tencent
China tencent open source team.
from t-962-improvements.