Infrared4Arduino is an object-oriented infrared library for the Arduino.

The library was (with some exceptions detailed below) written from scratch by myself. It uses Michael Dreher's IrWidget (article in German), see also this forum contribution.

The main inspiration for the present work was the well-known library called IRremote, published by Ken Shirriff in his blog, now hosted on GitHub. Chris Young's IRLib, (GitHub repo), should also be mentioned as a source of inspiration, but not of code. The SAMD21 support (Arduino Zero and others) is based on issues in the IRremote repository, and in particular this pull request. I am also indebted to this thread in the Arduino forum. The ATMega4809 support (Arduino WiFi Rev 2 and Arduino Nano Every) is based upon this PR. The Arduino Due support is basically taken from this project, which is licensed under the LGPL 2.1 license. The Teensy 3.x support is based upon code in IRremote. The ESP32 support is based upon this pull request.

The classes IrWidget and IrWidgetAggregating are based on Michael's code. The classes IrReceiverSampler and IrSenderPwm, are adapted from Kevin's work. The remaining files are almost completely written from scratch.

This work is a low-level library (like IRremote and IRLib) that can be used in other projects, like AGirs, which is an high-level program taking commands interactively from a user or a program through a bi-directional Stream. The goal has been to provide a sound, object oriented basis for the fundamental basis, not to provide maximal functionality, the maximal number of protocols supported, or the most complete support of different hardware. A clean design and high readability, without being "too" inefficient, has been the highest priority. Dynamic memory allocation with new and delete is used extensively. The user who is afraid of this can create his required objects at the start of the run, and keep them. Most classes are immutable. The classes are const-correct.

Here we list a (subjective!) selection of generic IR libraries for Arduino, with some (very personal) comments.

The original, that spawned all the rest! Now hosted here. Unfortunately since several years "stale"; personally I have 3 pull requests open... License: LGPL2.1 (although a migration to MIT has been discussed).

Subjectively, this is a cleaned-up and modernized version of IRremote. The basic structure is very similar, and it thus suffers from many of the basic problems of IRremote. It comes with a very ambitious PDF manual (125 pages!) entirely written by hand (not using a documentation system like Doxygen). It supports most 8 bit AVRs and SAMDs, but not ESPs. The libraries are not available in the Arduino library manager, however they are available on PlatformIO. Licenses: LGPL2.1 (IRLib), GPL3 (IRLib2).

This library, as the name suggested, was created as a fork of IRremote, supporting ESP8266 and ESP32 only. Has evolved considerably since the fork new features, in particular, it also contains support for a large number of specialized protocols, like air conditioning protocols. License: LGPL2.1.

This "lightweight" library is written with the aim of minimal foot print on very small systems, like the ATTiny. License: MIT-like.

Feel free to open issues at Github should the need or desire arise. A possible place to discuss is the Home automation or the Sensor sub-forums at the Arduino forum.

A fairly large numbers of examples are provided. Most of these are a straight-forward demonstration of a particular class, as indicated by the name.

However, one "example" is not really an "example" but a deployment program:

This "example" implements a Girs server for the Arduino. It can be used with IrScrutinizer, and Lirc (using the Girs driver). It is an interactive server that can send and receive IR signals, with some bells and whistles. The interactive server is mainly meant for interact with other programs. communicating over a serial line, likely in USB disguise.

MicroGirs is essentially a simplified version of AGirs, stripped of features seldomly used (LCD and (visible-light) LED support, Ethernet, etc). As opposed to AGirs, it does not depend on other libraries. For more documentation, see the AGirs project.

There are a number of configuration options. These are all contained in the file config.h and consists of CPP #defines.

MicroGirs is essentially functionally equivalent to "GirsLite".

Unfortunately, it is not yet working on SAMD as well as ESP and Teensy.

admin Up-to-date API, generated by Doxygen.

There are some project specific data typedefs in InfraredTypes.h. For durations in microseconds, the data type microseconds_t is to be used. If desired/necessary, this can be either uint16_t or uint32_t. For durations in milliseconds, use the type millisecons_t. Likewise, use frequency_t for modulation frequency in Hz (not kHz as in the IRremote/IRLib).

For "sizes", size_t, the standard C type, is used.

Implementation dependent types like int are used if and only if it is OK for the compiler to select any implementation allowed by the C++ language.

unsigned int is used for quantities that can "impossibly" be larger than 65535. It is believed that (unsigned) int is the fastest type for doing arithmetics, containing 16 bits or more.

An IrSequence is a vector of durations, i.e. sequence of interleaving gaps and spaces. It does not contain the modulation frequence. As opposed to IRremote and IRLib, our sequences always start with a space and end with a gap. It is claimed to be a more relevant representation than the one of IRremote and IRLib.

An IrSignal consists of a modulation frequency and three IrSequences: intro-, repeat-, and ending sequence. All of these, but not all, can be empty. If repeat is empty, intro has to be non-empty and ending empty. The intro sequence is always sent first, then comes a zero or more repeat sequences, and finally the ending sequence. To send a signal n > 0 times shall mean the following: If the intro is non-empty, send intro, n - 1 repeats, and then the ending. If the intro is empty, send n repeats, and then then ending.

The examples oppo_cooked and oppo_raw consist of IrScrutinizer exports of the infrared command set of the Oppo Bluray players, in parametrized and raw form respectively. The latter stores the raw signals in the flash area, "PROGMEM", (i.e. not taking up any (permanent) RAM storage) for which the API support is required. This is unfortunately not available with all architectures.

For some receiving and transmitting classes, multiple instantiations are not sensible, for others, it may be. In this library, the classes that should only be instantiated once are implemented as singleton classes, i.e. with no public constructor, but instead a static "factory" method (newThing()) that delivers a pointer to a newly constructed instance of Thing, provided that Thing has not been instantiated before. The classes, where multiple instances is sensible, come with public constructors. (However, the user still has to take responsibility for avoiding pin- and timer-conflicts.)

For hardware support, the file IRremoteInt.h from the IRremote project is used. This means that all hardware that project supports is also supported here (for IrReceiverSampler and IrSenderPwm). (Actually, a small fix, borrowed from IRLib, was used to support Arduinos with ATMega32U4 (Leonardo, Micro).) However, IrWidgetAggregating is currently supported on the boards Uno/Nano (ATmega328P), Leonardo/Micro (ATmega32U4), and Mega2560 (ATmega2560).

Several of the sending and receiving classes take a GPIO pin as argument to the constructor. However, the sending pin of IrSenderPwm and the capture pin of IrWidgetAggregating are not configurable, but (due to hardware limitations) have to be taken from the following table:

                                       Sender Pin      Capture Pin
Uno/Nano (ATmega328P)                       3             8
Leonardo/Micro (ATmega32U4)                 9             4
Mega2560 (ATmega2560)                       9            49
Due                                         7           n/a
Uno WiFi Rev2/Nano Every (ATmega4809)       6           n/a
Zero/M0 Pro/Nano Every IOT (ATSAMD21)       8           n/a
Teensy 3.x                                  5           n/a
ESP32                                       5           n/a

In some cases, this can be relatively easily changed in the code. A later version of the library may support more elaborate configuration.

The pin used by the the receivers (not to be confused with capture pins) can in general be selected freely, as long as it does not conflict with other requirements.

TODO.

All the receiving classes adhere to the following conventions: When initialized, it waits up to the time beginningTimeout for the first on-period. If not received within that period, it returns with a timeout. Otherwise, is starts collecting data. It will collect data until one of the following occurs:

• A silence of length endingTimeout has been detected. This is the normal ending. The detected last gap is returned with the data.
• The buffer gets full. Reception stops.

As opposed to other infrared libraries, there are no user changeable parameters as CPP symbols. However, the timer configuration is compiled in, depending on the CPP processors given to the compiler, see the file IRremoteInt.h.

As opposed to the predecessor projects, this project has a header (*.h) file and an implementation file (*.cpp, sometimes missing) for each public class.

Simple answer: there is none. If a function is sent erroneous data, it just silently ignores the request, or does something else instead. This (unfortunately) seems to be the standard procedure in Arduino programming.

I am used to exception based error handling, for some reason this is not used by the Arduino community.

Constructive suggestions are welcome.

Comparing with the predecessor works, this project may look meager, currently supporting only two protocols (NEC1 and RC5). It is planned to generate the corresponding C++ code automatically from the IRP notation. (For this reason, contributed implementations of more protocols are not solicited.)

RF signals (433 MHz and other carrier frequencies) do not use the IR typical modulation. Also there are a few IR protocols (like Revox, Barco, Archer) not using modulation. These signals can be sent by the class IrSenderNonMod, after connecting suitable hardware capable of sending non-modulated (IR- or RF-) signals to the GPIO pin given as argument to the constructor.

This library does not, as opposed to some of its competitors, implement hash codes. I do not consider this a very useful feature: If the received signals conforms to a known protocol, use the parameters (instead of a hash code). If it is not known, you need some form of meta-protocol in order to construct a hash code. It is very hard to define the decision criteria. I have yet to see a sensible use case for receiving signals as hash codes, i.e. where a hash-code based solution has advantages over other solutions.

IRLib and IRremoteESP8266 implements interrupt driven reception, but currently not this libary. It is planned.

This library does not, as opposed to some of its competitors, implement blinking. I do not consider this to be a sensible method of debugging -- using a logical analyzer together with Sigrok and Pulseview is a much better idea to do systematic debugging. Also for decoration and other "cool" light effects, there are better alternatives.

This library does not depend on any other libraries; only the standard Arduino environment.

• What is the difference between the IrReceiver* and the IrWidget* classes?

They are intended for two different use cases, receiving and capturing. Differently put, "receive" uses a demodulating receiver (TSOPxxx, etc.), "capture" a non-demodulating decoder (TSMPxxx, OPLxxx QSExxx, etc.). Note that this terminology is not universally accepted (yet!).

Your cooperation is solicited! Starting with testing, usage reports, bug reports and feedback (both code and documentation), over enhancements suggestions, to code and documentation contributions.

My goal is to write excellent code, even though I do not always succeed :-). "Everything as simple as possible, but not simpler." Cleanliness, logical structure, readability and maintainability are the most important requirements. Efficiency (runtime and/or space) is also important, although it normally comes on second place. The Arduino Style Guide has different goals (essentially optimizing for novice programmers, "Some of these run counter to professional programming practice"). It is therefore not given priority in this project.

The main documentation for the classes is found in the source files themselves. It can be extracted to a browse-able documentation using the program Doxygen. After installing the program, fire up the program in the source directory. It will generate documentation in a subdirectory html. To browse, open html/index.html in a browser.

The documentation is written for the user of the library, not the developer. For this reason, the file Arduino.h has been deliberately excluded from the documentation, to keep it centered on the main issues for the programming on the target system.

For someone used to, e.g., Netbeans or Eclipse, the Arduino IDE feels "somewhat" primitive and limited. In particular, it does not support debugging. Mainly for this reason, the code in the present library is designed to compile, and at least to some extent, run in a normal C++ environment on the host compiler. For this, some code modifications, in particular, a customized Arduino.h was needed. If the preprocessor symbol ARDUINO is defined, just includes the standard Arduino Arduino.h is included, otherwise (i.e. for compiling for the host), some more-or-less dummy stuff are defined, allowing compiling for, and execution/debugging on the host.

This way, certain types of problems can be solved much faster. The drawback is that the code is "polluted" with ugly #ifdef ARDUINO statements, which decreases readability and makes maintenance harder.

The subdirectory tests contains test(s) that run on the host. The supplied Makefile is intended for compiling for the host as target. It creates a library in the standard sense (*.a), and can be used to build and run tests in subdirectory tests.

With the provided Doxyfile, Doxygen will document only the (strict) Arduino parts, not the "portable C++".

The entire work is licensed under the GPL2 "or later" license. Ken's code is licensed under the LGPL 2.1-license. Michael's code carries the GPL2-license, although he is willing to agree to "or later versions".