This is a simple utility to tunnel link-layer traffic from a device accessible through a local network interface to a remote host via UDP to enable a basic VLAN.

The intended use case for this utility is to enable game consoles which support LAN network play (e.g. Xbox) to play on the Internet by creating a virtual LAN. To the console, it will appear as if other consoles are connected on the LAN.

Download the latest pre-built release for Windows here. At the moment, macOS and Linux users will need to build from source.

# Install mingw toolchain and download npcap SDK
wget https://nmap.org/npcap/dist/npcap-sdk-1.04.zip
unzip -dnpcap npcap-sdk-1.04.zip

# Compile
make l2tunnel.exe

# Compile
make

Additionally, once you have built the program, you will need to run it as root in order to permit it raw network access. You can apply "setuid" on the binary so it is always run as root, regardless of the user.

# Setuid to permit raw net access
sudo chown root l2tunnel
sudo chmod u+s l2tunnel

# Install libpcap
sudo apt install libpcap-dev

# Compile
make

Additionally, once you have built the program, you will need to either run it as root (not recommended) or set a capability on the executable to permit it raw network access. This can be done via:

# Set capabilities on the executable to permit raw net access
sudo setcap cap_net_raw,cap_net_admin=eip l2tunnel

This utility depends on libpcap to send and receive raw network traffic through a network interface.

Download and install the latest "Npcap installer" available here. Install in "WinPcap API-compatible Mode".

libpcap should be pre-installed.

Install libpcap-dev via:

sudo apt install libpcap-dev

The ideal setup is having the device you want to forward traffic to connected via Ethernet directly to a network port on your machine, or through a switch.

First, list the available network interfaces on the system:

$ ./l2tunnel list
device 0: vboxnet0
- flags: PCAP_IF_UP PCAP_IF_RUNNING
device 1: wlp0s20f3
- flags: PCAP_IF_UP PCAP_IF_RUNNING
device 2: enp0s31f6
- flags: PCAP_IF_UP PCAP_IF_RUNNING
[ additional interfaces trimmed ]

There are 3 interfaces shown here. The device I want to forward traffic for in this example is connected directly to interface number 2, enp0s31f6.

Next, we need to know the MAC address of the device in order to isolate its traffic from any other traffic on the network.

The MAC address can usually be found on the device itself or within a system configuration menu. Alternatively, if you do not know the MAC address of the device, we can monitor all traffic on the interface to determine the MAC address.

$ ./l2tunnel discover enp0s31f6
00:0d:3a:38:ac:2e to ff:ff:ff:ff:ff:ff

We see that a broadcast packet was sent by the device, and the source MAC address is 00:0d:3a:38:ac:2e.

Finally, we are ready to begin tunneling. We will tunnel traffic on local interface enp0s31f6 to/from our device with MAC address 00:0d:3a:38:ac:2e and remote host 1.2.3.4 via UDP port 1337 and receive traffic that will be forwarded back to the device via local UDP port 1337:

#                   (iface)      (mac addr)        (local addr) (remote addr)
$ ./l2tunnel tunnel enp0s31f6 -s 00:0d:3a:38:ac:2e 0.0.0.0 1337 1.2.3.4 1337

To create a simple VLAN (emulating a simple network hub), the hub.py script can be used. This script will listen on a specified UDP port for packets. Upon arrival of a packet from a given host, it will be forwarded to any other host which has also sent a packet.

To connect multiple consoles over the Internet, a hub should first be created. Then each user can start a tunnel which forwards traffic to the hub.