git clone https://github.com/pravega/pravega-benchmark
cd pravega-benchmark

./gradlew build

tar -xvf ./build/distributions/pravega-benchmark.tar -C ./run

<dir>/pravega-benchmark$ ./run/pravega-benchmark/bin/pravega-benchmark  -help
usage: pravega-benchmark
 -consumers <arg>               Number of consumers
 -controller <arg>              Controller URI
 -events <arg>                  Number of events/records if 'time' not
                                specified;
                                otherwise, Maximum events per second by
                                producer(s) and/or Number of events per
                                consumer
 -flush <arg>                   Each producer calls flush after writing
                                <arg> number of of events/records; Not
                                applicable, if both producers and
                                consumers are specified
 -help                          Help message
 -producers <arg>               Number of producers
 -readcsv <arg>                 CSV file to record read latencies
 -recreate <arg>                If the stream is already existing, delete
                                and recreate the same
 -scope <arg>                   Scope name
 -segments <arg>                Number of segments
 -size <arg>                    Size of each message (event or record)
 -stream <arg>                  Stream name
 -throughput <arg>              if > 0 , throughput in MB/s
                                if 0 , writes 'events'
                                if -1, get the maximum throughput
 -time <arg>                    Number of seconds the code runs
 -transactionspercommit <arg>   Number of events before a transaction is
                                committed
 -writecsv <arg>                CSV file to record write latencies

1. Burst Mode
2. Throughput Mode
3. OPS Mode or  Events Rate / Rate limiter Mode
4. End to End Latency Mode

For example:
<pravega benchmark directory>/run/pravega-benchmark/bin/pravega-benchmark  -controller tcp://127.0.0.1:9090  -stream streamname1  -segments 1  -producers 1  -size 100   -throughput -1   -time 60

The -throughput -1  indicates the burst mode.
This test will executed for 60 seconds because option -time 60 is used.
This test tries to write and read events of size 100 bytes to/from the stream 'streamname1'.
The option '-controller tcp://127.0.0.1:9090' specifies the pravega controller IP address and port number.
Note that -producers 1 indicates 1 producer/writers.

in the case you want to write/read the certain number of events use the -events option without -time option as follows

<pravega benchmark directory>/run/pravega-benchmark/bin/pravega-benchmark  -controller tcp://127.0.0.1:9090  -stream streamname1  -segments 1  -producers 1  -size 100   -throughput -1   -events 1000000

-events <number> indicates that total <number> of events to write/read

For example:
<pravega benchmark directory>/run/pravega-benchmark/bin/pravega-benchmark  -controller tcp://127.0.0.1:9090  -stream streamname5  -segments 5  -producers 5   -size 100   -throughput 10   -time 300

The -throughput <positive number>  indicates the Throughput mode.

This test will be executed with approximate max throughput of 10MB/sec.
This test will executed for 300 seconds (5 minutes) because option -time 60 is used.
This test tries to write and read events of size 100 bytes to/from the stream 'streamname5' of 5 segments.
If the stream 'streamname5' is not existing , then it will be created with the 5 segments.
if the steam is already existing then it will be scaled up/down to 5 segments.
Note that -producers 5 indicates 5 producers/writers .

in the case you want to write/read the certain number of events use the -events option without -time option as follows

<pravega benchmark directory>/run/pravega-benchmark/bin/pravega-benchmark  -controller tcp://127.0.0.1:9090  -stream streamname5  -segments 5  -producers 1  -size 100   -throughput 10   -events 1000000

-events 1000000 indicates that total 1000000 (1 million) of events will be written at the throughput speed of 10MB/sec

For example:
<pravega benchmark directory>/run/pravega-benchmark/bin/pravega-benchmark  -controller tcp://127.0.0.1:9090  -stream streamname1  -segments 1  -producers 5  -size 100  -events 1000   -time 60

The -events <event numbers>  (1000 ) specifies the events per second to write.
Note that the option "-throughput"  SHOULD NOT supplied for this OPS Mode or  Events Rate / Rate limiter Mode.

This test will be executed with approximate 1000 events per second by 6 producers.
This test will executed for 300 seconds (5 minutes) because option -time 60 is used.
Note that in this mode, there is 'NO total number of events' to specify hence user must supply the time to run using -time option.

For example:
<pravega benchmark directory>./run/pravega-benchmark/bin/pravega-benchmark  -controller tcp://127.0.0.1:9090  -stream streamname3  -segments 1  -producers 1 -consumers 1  -size 100  -throughput -1   -time 60

The user should specify both producers and consumers count  for write to read or End to End latency mode. it should be set to true.
The -throughput -1 specifies the writes tries to write the events at the maximum possible speed.