Comments (9)
To open the memory on the motor you press and hold the prog button on the back of the remote (use a paper clip or similar) until the motor jogs up and down. When it jogs it is indicating that the memory is open on the remote.
from espsomfy-rts.
Thanks for the quick reply. I've been pressing the prog button on the back of the remote and the battery powered Somfy motor responds by jogging and the switch on the motor starts to flash green. When I press the prog button within the app, the Somfy motor does not respond. The RF module is about 2 metres from the motor, I'm using Dupont leads to connect the RF module to the ESP32 mounted on a bread board and am wondering if they are too long at about 20 cms although I don't see any corruption receiving the data from the remote. I don't have another RF module to try as they are still on the boat. So I may move on to the tidied up version with shorter wiring.
from espsomfy-rts.
Double check your wiring. GDO0 (pin 3 on the transceiver) should be connected to the TX Pin. If you followed the guide that will be GPIO 13. GDO2 should be connected to RX (GPIO 12) or not connected at all. If you omit this wire you simply set RX and TX to GPIO 13 or 12 depending on where you wired it. The transceiver can receive from either pin and the software controls which mode it operates in.
from espsomfy-rts.
That fixed it. TX is now GPIO13 and RX is GPIO12. Paired first time. Thanks for your help and for a great project
from espsomfy-rts.
Yeah I need to update the pictures. You can build it either way and is just so happens that the picture was built differently than the table.
from espsomfy-rts.
Unfortunately I now have another problem. I have three blinds all bought at the same time. All three are outwardly identical with the same Somfy battery powered motor. Two of them are now paired but I can't get the third to pair. The motor responds to the single channel remote in the same way as the other two and it goes into pairing mode using the remote's prog button but it won't respond and pair to the ESP Somfy. Perhaps I should open a new issue?
from espsomfy-rts.
Is this third motor fully charged? Also, try to increment the address by 10 and see if it will pair. If it does then something occurred during the pairing process and the address ended up getting reserved in the motor. If this happens with a remote you need to reset the motor to factory settings and start over but in this instance, you can simply change the address.
from espsomfy-rts.
Yes, all the motors were fully charged. Anyway, changing the address by 10 allowed the blind to pair so something must have gone wrong with the original pairing attempt. I plan to factory reset the motor and start again from scratch. Thanks for your support, much appreciated.
from espsomfy-rts.
Closing this for now. Open a new issue if you have further problems.
from espsomfy-rts.
Related Issues (20)
- invalid header: 0x64616873 after Flashing with ESPHome HOT 2
- Now starting with USB power adaptar HOT 7
- Alert pictogram on rolling shutter HOT 3
- Stumbled over SLZB-06: might this be used for ESPSomfy-RTS? HOT 5
- Device occasionally unresponsive HOT 2
- MY simulation
- Shutter group HOT 13
- Control other RF Blinds HOT 5
- FYI: Interesting observation on rolling code HOT 3
- WiFi-problem HOT 13
- Boot Inestability HOT 8
- Network monitoring HOT 13
- FYI: Selfmade dipole antenna HOT 5
- Version 2.4.x HOT 4
- Somfy IO HOT 2
- Non-protected HTTP endpoints HOT 1
- Homekit HOT 2
- Add limit on the tilt movements when position is not at 100% HOT 3
- [Feature request] Zigbee support HOT 2
- Index.html not found HOT 12
Recommend Projects
-
React
A declarative, efficient, and flexible JavaScript library for building user interfaces.
-
Vue.js
🖖 Vue.js is a progressive, incrementally-adoptable JavaScript framework for building UI on the web.
-
Typescript
TypeScript is a superset of JavaScript that compiles to clean JavaScript output.
-
TensorFlow
An Open Source Machine Learning Framework for Everyone
-
Django
The Web framework for perfectionists with deadlines.
-
Laravel
A PHP framework for web artisans
-
D3
Bring data to life with SVG, Canvas and HTML. 📊📈🎉
-
Recommend Topics
-
javascript
JavaScript (JS) is a lightweight interpreted programming language with first-class functions.
-
web
Some thing interesting about web. New door for the world.
-
server
A server is a program made to process requests and deliver data to clients.
-
Machine learning
Machine learning is a way of modeling and interpreting data that allows a piece of software to respond intelligently.
-
Visualization
Some thing interesting about visualization, use data art
-
Game
Some thing interesting about game, make everyone happy.
Recommend Org
-
Facebook
We are working to build community through open source technology. NB: members must have two-factor auth.
-
Microsoft
Open source projects and samples from Microsoft.
-
Google
Google ❤️ Open Source for everyone.
-
Alibaba
Alibaba Open Source for everyone
-
D3
Data-Driven Documents codes.
-
Tencent
China tencent open source team.
from espsomfy-rts.