Comments (19)
・First question
Press BL_TOGG or RGB_TOG.
・Second question
I can only think of checking the soldering.
from ergodash.
Thanks for the reply! How do I press BL_TOGG or RGB_TOG?
EDIT: So i resoldered some of the misbehaving keys and they work great now. Now the only issue I have is with the LEDs. I set two different buttons on the keyboard, one as BL_TOGG and one as RGB_TOGG and neither of them do anything.
EDIT 2: now the entire HJKL: row isn't working on the right pad. It worked great last night and now I come into work and they don't do anything. Everything else works fine but I'm not sure why this would have changed just from bringing it into work, i was very gentle. Any help would be greatly appreciated.
from ergodash.
@nutimnot could you post a couple pictures of the boards? It might help rule out soldering as the culprit.
from ergodash.
@brethash here are some pictures. I got home just now and added some more solder to the mis-behaving keys and reflashed that side of the keyboard to no avail, the entire HJKL:" row is dead.
for reference, in the picture the middle row is the HJKL:" row
from ergodash.
from ergodash.
For an entire row that stopped working, it may be the pro-micro connection.
from ergodash.
@GreenShadowMaker how would i go about fixing that kind of issue?
EDIT: Follow up question, if it was working totally fine and then stopped, what would be the cause of that? I didn't do any soldering or anything and it stopped working, the row that is.
from ergodash.
I managed to fix the issues with the HJKL row. One of the points on the Pro micro wasn't soldered well, so I remelted it and now it's fully functional (typed this reply on the keyboard). If anyone knows why the LEDs aren't working let me know. I don't have any resistors set up, the kit only came with diodes.
from ergodash.
@nutimnot you won't need any additional resistors for the undermount LEDs to work. The resistors are only needed for the backlight/switch LEDs.
If you're using the default keymap for the keyboard, try flashing @GreenShadowMaker 's keymap. It seems like his has the undermount LEDs on by default (at least thats what it seemed like when I flashed it anyway). The layers in his keymap are also a bit easier to work with in my opinion.
from ergodash.
@brethash where can I find their keymap?
from ergodash.
The keymap is here and the layout itself is here. To toggle the adjust
layer, the raise and lower keys are pressed at the same time (for me they were the keys directly below the B
and the N
.
from ergodash.
Awesome thank you! Now I'd just try flashing it with QMK and see if it works yeah?
from ergodash.
Yep! You should be able to build/flash it with make ergodash/rev1:greenshadowmaker:avrdude
from the root of the QMK
folder.
from ergodash.
@brethash how do you do that using the QMK toolbox?
from ergodash.
@nutimnot that's a good question! I've actually not used the QMK toolbox before; I always just build and flash from the command line, so I'm not sure how it works. 😞
from ergodash.
I flashed it but it didn't turn on the LEDs so i'm not sure. Maybe I will try something else or test to see if the LEDs work at all I guess. Thank you @brethash for all your help my guy
from ergodash.
You haven't done the RGB jumper connetion.
You have to read this.
https://github.com/omkbd/ErgoDash/blob/master/Doc/build-en.md#5-underglow-led-optional
from ergodash.
@omkbd So I just have to solder those two connections at the top of the board? I shouldn't need anything other than some solder, right? I don't have any resistors installed or anything. I'll try it out this week
from ergodash.
I got it to work, thank you @omkbd and @brethash for y'alls help <3
from ergodash.
Related Issues (20)
- A problem I don't understand. Please help me
- Confusion about spacers
- Plans to add revision 1.3 or 2.0 PCB schematics and spec? HOT 12
- Is EE_HANDS supported? HOT 1
- Making the pcb and case Alps friendly. HOT 1
- M2 spacers height HOT 3
- MJ-4PP-9 TRRS jack not available in europe HOT 1
- Hole size for Pro-Micro's too small for Hotswap sockets HOT 1
- arcgis
- Sugestion: Increase extra thumb key connection pads to 4mm each (JLCPCB Audit failing)
- Update parts list for M2x6mm spacer to "M2×6mm threaded spacer"
- parts says 66-70 keys, couldn't you use 72? HOT 2
- Alternative for the MJTP1117 switch HOT 2
- Possible substitute for IRLML6344TRPbF
- Reset is not working while flashing HOT 3
- Slave Hand RGB Underglow not working HOT 1
- Underglow RGB LEDs not working on both sides HOT 2
- Firmware link broken HOT 2
- Via cannot detect my ergodash HOT 1
- Adds led lights for the top edge
Recommend Projects
-
React
A declarative, efficient, and flexible JavaScript library for building user interfaces.
-
Vue.js
🖖 Vue.js is a progressive, incrementally-adoptable JavaScript framework for building UI on the web.
-
Typescript
TypeScript is a superset of JavaScript that compiles to clean JavaScript output.
-
TensorFlow
An Open Source Machine Learning Framework for Everyone
-
Django
The Web framework for perfectionists with deadlines.
-
Laravel
A PHP framework for web artisans
-
D3
Bring data to life with SVG, Canvas and HTML. 📊📈🎉
-
Recommend Topics
-
javascript
JavaScript (JS) is a lightweight interpreted programming language with first-class functions.
-
web
Some thing interesting about web. New door for the world.
-
server
A server is a program made to process requests and deliver data to clients.
-
Machine learning
Machine learning is a way of modeling and interpreting data that allows a piece of software to respond intelligently.
-
Visualization
Some thing interesting about visualization, use data art
-
Game
Some thing interesting about game, make everyone happy.
Recommend Org
-
Facebook
We are working to build community through open source technology. NB: members must have two-factor auth.
-
Microsoft
Open source projects and samples from Microsoft.
-
Google
Google ❤️ Open Source for everyone.
-
Alibaba
Alibaba Open Source for everyone
-
D3
Data-Driven Documents codes.
-
Tencent
China tencent open source team.
from ergodash.