liweiyap / mycpu Goto Github PK

myCPU.cpp contains the main() function for simulating a stack-based CPU. The CPU contains an operand stack and a register, and it also has access to memory.

• The stack is used to store the results of computations during the processing of machine instructions. It is implemented as a LIFO object in the header file headers/stack.hpp.
• The register acts as a Program Counter (PC) that points to the address of the next machine instruction to be executed. It is implemented as an unsigned int in the helper file include/simulation.cpp.
• Machine instructions to be processed are first stored in a contiguous array in the memory. Each instruction is 32 bits wide; the first eight bits are the opcode and the last 24 bits are the operand that will eventually be stored on the stack. Each opcode will call one of the functions in the helper file include/stack_execute.cpp, which will execute a computation through the manipulation of the stack. The results of some of the computations may be written to the standard output until the final machine instruction is processed.

The main() function requires three types of variables from the standard input.

1. The type of mode: either disassemble or simulate.
2. The number of machine instructions to be stored in the memory as an array.
3. All machine instructions to be stored. Each instruction should be input as a hexadecimal but stored in the memory as a signed 32-bit integer (or int32_t). The first two hex-nibbles (or eight bits) of each hexadecimal represent the opcode, whilst the last six hex-nibbles (or 24 bits) represent the operand.

Depending on the type of mode, we get slightly different results written to the standard output. The disassembly mode translates all instructions in the memory array into a human-readable form so that we can understand each machine instruction. The simulation mode executes all the instructions in the memory array using the operand stack and the register.

Let's say that we wish to simulate the following C++ code:

int i = 10;
while (i != 0){
    std::cout << i;
    --i;
    std::cout << "\n";
}
std::cout << "\n";

To simulate this code, we input the following when running the main() function in myCPU.cpp:

simulate
16
0x3200000f
0x30000000
0x26000000
0x26000000
0x32000000
0x4100000e
0x12000000
0x32000001
0x21000000
0x3200000f
0x31000000
0x3200000a
0x13000000
0x40000000
0x1000000
0xa

As expected, this will return the following output:

10
9
8
7
6
5
4
3
2
1

To understand how myCPU.cpp has simulated the C++ code, we can re-run the same inputs -- but this time with disassemble rather than simulate. This will then call the helper functions in the file include/disassembly.cpp. Below, we show again the inputs, but this time with the output of the disassemble mode as comments on the right hand side.

disassemble  // OUTPUT OF DISASSEMBLY AS COMMENTS   |   MEANING IN C++
16           // ------------------------------------|-------------------------
0x3200000f   // const   15  ;   load i for ...      |
0x30000000   // load        ;   ... decrement       |
0x26000000   // dup         ;   ... output          |
0x26000000   // dup         ;   ... test            |   int i = 10;
0x32000000   // const    0  ;   if i == 0           |   while (i != 0){
0x4100000e   // jeq     14  ;     jump to halt      |
0x12000000   // out         ;   output i            |       std::cout << i;
0x32000001   // const    1  ;   decrement i         |       --i;
0x21000000   // sub         ;                       |
0x3200000f   // const   15  ;                       |
0x31000000   // store       ;   store i             |
0x3200000a   // const   10  ;   output newline      |       std::cout << "\n";
0x13000000   // outchar     ;                       |
0x40000000   // jmp      0  ;   jump to start       |   }
0x1000000    // hlt         ;   stop program        |
0xa          // data   0xa  ;   variable i          |
             // end                                 |   std::cout << "\n";

More test cases can be found in tests/myCPU_tests.cpp.

To create a local copy of this repository, simply click 'Download'. Alternatively, clone it by first navigating to the path you want to store the local copy and then executing the following on the command line:

git clone [email protected]:liweiyap/MyCPU.git

Compilation relies on the CMake build system. The code has been tested with recent versions of the Clang C++ compiler. To compile and run, execute the following in the root of the repository:

mkdir build
cd build
cmake ..
make all
./myCPU

After executing make all, we can also run the test cases:

./tests/myCPU_tests

Full credits for the header file headers/catch.hpp go to the authors of Catch2. This allows for easy testing in tests/myCPU_tests.cpp by using a header-only library.

This repository was inspired by a coursework from a prerequisite course called Informatik I in the first semester of my master's studies in computational biology. The lecturer of this course was Prof. Felix Friedrich.