Errors and then only 404 pages after clicking on main page Temp Bar or Control point: Keg Sensor link about keg-cop HOT 17 CLOSED

I don't have temperature sensors hooked up at the moment (insert long story/standard disclaimer about me moving), so I need to get that set up before I can do any testing. I have if/then blocks in C++ and JS to take different paths if there are no temp sensors detected.

from keg-cop.

Your comment made me think about my configuration. I have space in the single-sided PCB for 3 temp sensors, but only have one connected at the moment. I checked my Keg Cop config and see that I had those 2 other sensors enabled (though not connected/used now). Thinking this might be the cause of the error and the 404 loop, I disabled all but the one sensor actually connected at this moment....but it didn't make any difference. Still the same error messages as well as the 404 loop after clicking on those two links mentioned above.

from keg-cop.

Yeah either way it should not 404 so I broke something. :)

from keg-cop.

Took care of the 404 loop under #60, which was a separate issue. Looking at the reason the temps page is broken now.

from keg-cop.

This is fixed in devel. Testing release.

from keg-cop.

from keg-cop.

Give me about an hour to push a new devel version. I think I have it licked.

from keg-cop.

Okay - devel should be good to test.

from keg-cop.

from keg-cop.

from keg-cop.

When you choose a tap, it shows in the GUI the correct tap number for all except for Tap 9 (It says Tap 8 Configuration)

Man if that's all you've found I did pretty good! :)

Got it, fixed in my local version and will be in the release.

from keg-cop.

Okay - your email responses are getting messy and I am missing things. Can you trim the old responses when you reply?

I also noticed a spelling error – Temperatire

Added #68

When you choose a tap, it shows in the GUI the correct tap number for all except for Tap 9 (It says Tap 8 Configuration)

Added #69

When looking at the “Temperatures” page and clicking on one of the tan/orange temperatures shown, it goes to a bad link (see in the screenshot below)

No images come through when you reply via email. You either need to click on the "View in GitHub" or describe more thoroughly. Right now I am unable to reproduce this one.

I can’t calibrate the flow meter with the new devel firmware. I was able to successfully calibrate it in 1.0.0, however.

When I go to the calibrate page, Select Tap 9 (that’s the one and only I’m using since the 1-sided PCB made it easier), Config by volume, enter in some ounces measured, but don’t get a 0 to show up in the Pulses box until the flow starts. No pulses seen at all.

Not following here either. You should not enter ounces until after you have dispensed the volume, then enter ounces, then it should calibrate. Is that not working like that?

from keg-cop.

from keg-cop.

When calibrating the flow meter I choose the correct tap (#9) and then check the Volume button and press “Do Config by Volume". In the older versions of firmware, on the next screen a 0 would populate right away in the Pulses box and when I got some flow going, the count would increase. In the Development firmware, a zero doesn’t immediately show up in the Pulses box and nothing happens when get some flow going. Pulses don’t increment, but the fact that it behaves different between v1.0.0 and devel makes me think it’s a firmware/coding problem and nothing on my end. It doesn’t matter whether I enter any ounces first or not, it doesn’t appear to count pulses. I’ve tried choosing different Tap numbers and that doesn’t make any difference either (didn’t expect it to though).

I've opened #70 for this.

Be sure to follow the new issues for these, as this one was for the 404 and is closed.

from keg-cop.

Updated Keg Cop Beta to 1.1.1-Beta.2

from keg-cop.

from keg-cop.

Moved these to #149 and #150.

from keg-cop.