This is a repository for my Marlin 2.0.x config files for the Wanhao D6+ (Bondtech & Microswiss)

• Merge up to Marlin 2.12 Changes to default - Config.h:
• #define STRING_CONFIG_H_AUTHOR "K41C"
• #define MOTHERBOARD BOARD_ULTIMAIN_2
• #define CUSTOM_MACHINE_NAME "Wanhao D6+BM"
• #define PSU_CONTROL
• #define PSU_NAME "Power Supply"
• #define PS_ON_PIN 24 // Wanhao
• #define TEMP_SENSOR_0 20
• #define BED_MAXTEMP 115
• //#define PIDTEMP
• #define MPCTEMP
• #define PIDTEMPBED
• //#define THERMAL_PROTECTION_CHAMBER
• //#define THERMAL_PROTECTION_COOLER
• #define ENDSTOPPULLUP_XMIN
• #define ENDSTOPPULLUP_YMIN
• #define ENDSTOPPULLUP_XMAX
• #define ENDSTOPPULLUP_YMAX
• #define ENDSTOPPULLUP_ZMAX
• #define X_MIN_ENDSTOP_INVERTING true
• #define Y_MIN_ENDSTOP_INVERTING true
• #define Z_MIN_ENDSTOP_INVERTING true
• #define DEFAULT_AXIS_STEPS_PER_UNIT { 80.0395, 80.0395, 400.48, 415 }
• #define DEFAULT_MAX_ACCELERATION { 3000, 3000, 100, 500 }
• #define DEFAULT_ACCELERATION 1500
• #define DEFAULT_RETRACT_ACCELERATION 1500
• #define DEFAULT_EJERK 1.0
• #define S_CURVE_ACCELERATION
• //#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
• #define PROBE_MANUALLY
• #define INVERT_X_DIR true
• #define INVERT_Y_DIR false
• #define INVERT_Z_DIR true
• #define INVERT_E0_DIR true
• #define HOME_AFTER_DEACTIVATE
• #define Y_BED_SIZE 183 //Important Bondtech
• #define Z_MAX_POS 185
• #define MESH_BED_LEVELING //??
• #define LEVEL_BED_CORNERS
• #define XY_SKEW_FACTOR 0.0
• #define XZ_SKEW_FACTOR 0.0
• #define YZ_SKEW_FACTOR 0.0
• #define PREHEAT_1_TEMP_HOTEND 190
• #define PREHEAT_2_LABEL "PETG"
• #define PREHEAT_2_TEMP_HOTEND 230
• #define PREHEAT_2_TEMP_BED 70
• #define NOZZLE_PARK_FEATURE
• #define SDSUPPORT
• #define SLIM_LCD_MENUS //??
• #define ENCODER_PULSES_PER_STEP 2
• #define ENCODER_STEPS_PER_MENU_ITEM 1
• #define REVERSE_ENCODER_DIRECTION
• #define ENCODER_NOISE_FILTER
• #define INDIVIDUAL_AXIS_HOMING_MENU
• #define SPEAKER
• #define LCD_FEEDBACK_FREQUENCY_DURATION_MS 5
• #define LCD_FEEDBACK_FREQUENCY_HZ 5000
• #define OLED_PANEL_TINYBOY2
• #define LCD_RESET_PIN 5
• #define PCA9632

Changes to default - Config_adv.h:

• #define THERMAL_PROTECTION_BED_PERIOD 70
• #define WATCH_BED_TEMP_PERIOD 70
• #define FAN_KICKSTART_TIME 100
• #define CASE_LIGHT_ENABLE
• #define CASE_LIGHT_PIN 8
• #define CASE_LIGHT_DEFAULT_BRIGHTNESS 255
• #define CASE_LIGHT_MENU
• #define QUICK_HOME
• #define ADAPTIVE_STEP_SMOOTHING
• #define MOTOR_CURRENT_PWM_RANGE 2782
• #define PWM_MOTOR_CURRENT { 1200, 1200, 1000 }
• #define LCD_INFO_MENU
• #define USE_SMALL_INFOFONT
• #define LCD_SERIAL_PORT 3
• #define BABYSTEPPING

• #define DOUBLECLICK_FOR_Z_BABYSTEPPING
  

• #define LIN_ADVANCE
  

• #define EXPERIMENTAL_SCURV
  

• #define MINIMUM_STEPPER_POST_DIR_DELAY 200
  

• #define MINIMUM_STEPPER_PRE_DIR_DELAY 200
• #define MINIMUM_STEPPER_PULSE 1
• #define MAXIMUM_STEPPER_RATE 500000
• #define ADVANCED_PAUSE_FEATURE

Wanhao D6 BMG Upgrade https://www.bondtech.se/product/wanhao-d6-kit/

All Metal Hotend with SLOTTED Cooling Block for Duplicator 6 https://store.micro-swiss.com/products/all-metal-hotend-with-slotted-cooling-block-for-duplicator-6

Installing AVRDUDE

Make sure your USBASP is plugged into the Raspberry PI and the the cable is plugged into the ICSP port.

SSH Into your Raspberry PI running Octoprint using Bitvise SSH:

https://www.bitvise.com/ssh-client-download

Via the Terminal enter the following lines one at a time:

sudo apt-get update sudo apt-get upgrade sudo apt-get install avrdude

Verify the avrdude installation location by entering:

which avrdude

Copy the firmware to your /home/pi directory Raspberry PI using Bitvise:

Enter the follow command to flash the firmware to the Wanhao D6:

root@octopi:/home/pi# avrdude -c usbasp -p m2560 -u -U flash:w:firmware.hex

Once the flashing is finished the printer will restart.

Tweaking your settings. 3D Printers are not tools you can set it and forget it.

1. My print environment will not be the same as yours and this is true for any printer settings you obtain online. You will need to make sure to PID Autotune for the bed and the extruder. My hotend is wrapped in fiberglass shield heat tape. I have a printer room and I enclosed the sides of my printer so there is no air conditioning interfering with my prints.
2. You will need to goto your slicer of choice and adjust your retraction settings. I print mainly ABS on this printer.
3. You will need to save your firmware settings via m500.
4. When using a Microswiss Hotend you will need to do Temperature tests with every filament you use. The temp needed to print could be +/- 10-15 degrees and this is normal.
5. Dry your filaments before use. Don't assume any filament you use is dry. It can be wet from the day it was made, plastic allows moisture through it over time. New filament only means New to You. It doesn't mean that it hasn't been sitting on a dock or in a wharehouse somewhere for months.

Octoprint I use Octoprint with this printer. You will want to make sure to download any plugins you need to control the printer. https://octoprint.org/download/