• 1. Install Prerequisites
• 2. Supported Boards
• 3. Build
  • 3.1 T-SIM7000G
  • 3.1 T5-4.7
  • 3.2 T-CALL SIM800
  • 3.3 T-PicoC3
  • 3.4 T5-4.7 Plus
  • 3.5 T-Echo
  • 3.6 T-Display
  • 3.7 T-DisplayS3
  • 3.8 T-RGB
  • 3.9 T7-S3
  • 3.10 T-DisplayS3-AMOLED
• 4. Modules
  • 4.1 Display Module
• 5. Interesting Project
• 6. Issue
• 7. Future plans

To compile with lilygo-micropython you need to get the following packages. The command to run depends on which distribution of Linux you are using:

• Ubuntu and Debian:

sudo apt-get install git make python3 python3-pip cmake quilt

• LILYGO T-SIM7000G
• LILYGO T5-4.7
• LILYGO T-T-CALL SIM800
• LILYGO T-PicoC3
• LILYGO T5-4.7 Plus (esp32s3)
• LILYGO T-Echo
• LILYGO T-Display
• LILYGO T-DisplayS3
• LILYGO T-RGB
• LILYGO T7-S3
• LILYGO T-DisplayS3-AMOLED

$ cp config_T-SIM7000G config
$ make

$ cp config_T5-4.7 config
$ make

$ cp config_T-CALL config
$ make

$ cp config_T-PicoC3 config
$ sudo apt install gcc-arm-none-eabi libnewlib-arm-none-eabi build-essential
$ make

$ cp config_T5-4.7-Plus config
$ make

$ cp config_T-Echo config
$ make

Use circuitpython by default

To use micropython, you need to modify the config file:

--- config_T-Echo       2022-07-13 17:11:04.374660308 +0800
+++ config      2022-07-13 17:11:00.694565940 +0800
@@ -1,3 +1,3 @@
 CONFIG_TARGET=nrf
 CONFIG_BOARD=LILYGO_T-Echo
-CONFIG_MICROPYTHON_CORE=circuitpython
+# CONFIG_MICROPYTHON_CORE=circuitpython

$ cp config_T-Display config
$ make

$ cp config_T-DisplayS3 config
$ make

$ cp config_T-RGB config
$ make

$ cp config_T7-S3 config
$ make

$ cp config_T-DisplayS3-AMOLED config
$ make

• epd: LilyGo-EPD47 using in micropython.
• framebuf1: This module provides a general frame buffer which can be used to epd module.
• st7789: Fast MicroPython driver for ST7789 display module written in C.
• bma: micropython driver library for bma423
• lcd: Driver library supporting I8080 and RGB interface
• framebuf_plus: Added gfx font support on the basis of framebuf.

LilyGo-EPD-4-7-OWM-Weather-Display: Using the LilyGo EPD 4.7" display to show OWM Weather Data

Compilation gives the following error:

```
ninja: build stopped: subcommand failed.
ninja failed with exit code 1
make[1]: *** [Makefile:42: all] Error 2
make[1]: Leaving directory '/home/scruss/c/lilygo-micropython/build_dir/esp32s3/micropython/ports/esp32'
make: *** [Makefile:36: all] Error 2
```

Please uninstall ninja and try to compile again

```shell
sudo apt remove ninja-build
rm build_dir -rf
```

• Support menuconfig
• More boards
• Complete development documentation