Online Water Meter Programmer..

Water meters are devices that measure how much water you use. They have a spinning disk inside them, and each time it spins all the way around, it means you've used one liter of water. Most water meter readers use a simple method: they check if a metal disk is there or not. But the Muino water meter is different. It uses three light sensors to keep track of where the disk is. It uses some smart techniques to do this, and we use calculate with some fine adjustments to get things just right. This helps the Muino water meter measure very accurately, down to almost a millimeter. But remember, the spinning disk doesn't move perfectly like a smooth wave. So, in some parts of its rotation, the measurements might jump a bit more than in other parts.

The Muino Smart Water Meter is a single-board device that measures water consumption with sub-100 millilitre accuracy. The other big benefit is the ease of installation, for friends/family that wanted a similar solution this is easier to use.

• If you would like the watermeter go to: tindie-webshop or better my own-webshop
• You want a sensor to play with the DIY version go to: tindie-webshop or better my own-webshop
• For big orders please make a request: email
• My webshop is located at muino.nl. I haven't dedicated time to enhancing the visual appeal of my site. However, I prefer nowadays my own website, because some people just buy it without knowing what they buy and using Tindie's protection scheme let me pay for all of the shipping costs. So in the end I am wrong and therefore I request a higher price from tindie webshop than from my own webshop, sorry I have to.

• KiWa V200 (Designed for)
• Honeywell v200 (Designed for)
• KiWa R400 (Similar to Sensus 620)
• Sensus 620 (needs slight enlarging of two holes, and placement looks maybe less nice)
• Elster Honeywell (some)
• Itron Actaris Schlumberger (Aquadis+) with double-sided tape or tie-wraps.
• You can always donate to let me create a watermeter compatibility..

Thank you for buying the Muino Water Meter Reader :). Let me try to explain the steps for your installation!

• USB-C cable that can power the Muino Smart Water Meter
• Device with WiFi for initial connection to your home wifi network
• Access to your Home-assistant

1. Place the Muino Smart Water Meter on your water-meter, where applicable use M2.5/M4 screws/bolts to attach. Screws are intented to fit securely/snuggly in the PCB but do not over thighten. Less compatible meters have no or wrong mounting holes, use tie-wraps, tape and creativity...
2. Connect the USB-C power
3. Go to your phone/wifi-device and connect to the Muino Smart Water Meter WiFi SSID (if you need a password: 12345678)
4. On the device connected to the Muino Smart Water Meter, go to http://192.168.4.1 and select your prefered WiFi SSID to connect the Muino Smart Water Meter with and enter the SSID passcode.
5. The Muino Smart Water Meter will try to connect to the selected WiFi SSID, please be patient. After a while, check your home network to find the IP-address of the Espressif Muino Smart Water Meter.
6. In Home Assistant, go to Settings, add the ESPHome integration, and add IP-address of the Muino Smart Water Meter to adopt it.
7. In Home Assistant, go to Energy -> Energy Configuration (3 dot menu), add the new sensor (sensor.liters) and potentially the price per cubic meter of water.

1. After restart: Upon restart, a zero value is sent to inform the home assistant that the sensor has been reset.
2. Calibration: The sensor calibrates during the first 2 liters of water usage.
3. Sending Updates: After calibration, the sensor sends updates to the home assistant system. It waits until it detects 2 liters of water usage and then pauses for 1 minute before sending the update. This prevents interruptions during activities like showering.

docker run --rm --privileged -v  ${PWD}:/config   -it ghcr.io/esphome/esphome run  --device=/dev/ttyACM0 "muino-water-meter-esp32.yaml"

# for windows builds are done using WSL
# Open following in admin powershell
usbipd wsl list

# select  the one to connnect
usbipd wsl attach --busid <busid>