Simplest DIY Low Power, low cost, Local standalone or web connected IOT Network (no third party software or cloud service or programming knowledge required)

This is the main goal of this project. Proberequest protocol is used for data transfer to conserve power.

Whole network can be monitored and controlled using any android or ios MQTT front end dashboard client app like MQTT Dash thereby making it very simple to implement.There is also very simple but powerful dashbord to monitor sensor data from whole network using uPlot graphing library and built in webserver. Sensor data of whole network is stored on gateway device using SPIFFS file system. The web interface is simple one page but powerful enough to monitor and control whole network of devices. Web interface could be customised any way you want live by changing html, css or javascript code using built in SPIFFSEditor library without recompiling or reuploading files.Changing data format in SPIFFS also possible live from web interface using SPIFFSEditor.

No need to charge small 100 mAh LIR2450 coin cell battery manually for life of battery or solar cell if LIR2450 coin cell battery and 53mmx30mm small solar cell is used.

Average sensor node could be below $5 each.

Simply storing single standard .bin file for all remote devices to Gateway SPIFFS file system and publishing MQTT command from MQTT client app or by issuing command from web interface each sensor device on the network can be updated with latest firmware. Again there is no need to physically access hard to reach remote devices.

This code can create small standalone network (maximum of 100) of battery powered WiFi devices connecting to one ESP32 gateway device in star network topology. Each device can be controlled simply by MQTT app like MQTT Dash or built in web interface over local network or over internet if used with DynDNS service like DuckDNS. There is no need for other home automation software locally or on cloud.

My testing shows data communication is achieved within 80 milliseconds total uptime for remote device out of which only 45 milliseconds of time used for more power hungry WiFi receive & transmit on average thereby saving significant battery power. I think this is better than ESPNow protocol.

• To test the code at minimum 1 remote ESP32 and 1 ESP32 Gateway device are required.
• One device (always on and mains powered) use gateway sketch and another device (sleeping most of the time and battery powered) use remote code.
• There are .bin files for gateway and remote sketches in their respective folders if do not want to compile the code.
• Please format flash as SPIFFS file system and upload data folder within Simple Gateway folder.
• New remote device will show up with device ID 246 but the device ID can be changed to any other unused ID on network from web interface or MQTT client.
• There can be as many as 100 battery powered devices which can send data to one gateway device.
• Web interface is started at IP 192.168.4.1 if connected to AP named "ESP" and shows graphs of sensor data from whole network, It also allows to issue commands to any remote device on network.

commands are issued via MQTT payload with topic name "command/" or using dropdown menu at built-in web interface. At least first three commands are necessary.

- Device ID must be 2 or 3 digits and ending with 2,6,A or E to avoid conflict with other devices.
- See https://serverfault.com/questions/40712/what-range-of-mac-addresses-can-i-safely-use-for-my-virtual-machines.
- Any of following for device ID is valid.
- 06,16,26,36,46,56,66,76,86,96,106,116,126,136,146,156,166,176,186,196,206,216,226,236,246.

- value 101 to 121 is reserved for following commands:

 - 101 =     Digital Write.
           - Example command payload 36/101/<01 to 05 or 12 to 39>/<00 0r 01>/ for digitalWrite.
           
 - 102 =     Analog Write.
           - Example command payload 36/102/<01 to 05 or 12 to 39>/<1 to 256>/ for analogWrite(pwm).
 
 - 103 =     Digital Read.
           - Example command payload 36/103/<01 to 05 or 12 to 39>/
 
 - 104 =     Analog Read.
           - Example command payload 36/104/<01 to 05 or 12 to 39>/
 
 - 105 =     Neopixel.
           - Example command payload 36/105/<00 to 256>/<00 to 256>/<00 to 256>/<00 to 256>/
           
 - 106 =     Set target values.
             It is posiible to send and store 4 target values to remote device for further automation locally in remote device.
           - Example command payload 36/106/<00 to 256>/<00 to 256>/<00 to 256>/<00 to 256>/
 
 - 107 =     Set WiFi Channel.
           - Example command payload 36/107/<00 to 14>/
           
 - 108 =     Set device mode - device mode 0 = normal mode and device mode 1 = OTA update.
           Mainly used for OTA update but can be used to run any alternative Code block.
           - Example command payload 36/108/<00 to 105>/ 
 
 - 109 =     Set sleep time in minutes.
           - Example command payload 36/109/<00 or 255>/
 
 - 110 =     Set device ID.
           - Example command payload 36/110/<00 or 255 if number ends with 2, 6, A, or E>/
           
 - 111 to 120 reserved for future expansion.
 
 - 121 =     Set sensor types for each device.
           - Example command payload 36/121/<00 to 256>/<00 to 256>/<00 to 256>/<00 to 256>/

- pinNumber in case of command type 101 to 105 above. 
- Value1 in case of command type 106,107,108,109 & 110 commandtype.

Most suitable use cases around typical home - Light control, fan/AC control, Weather Station, Door/Window sensor, Water/Oil tank level sensor, Presence Detection/motion sensor, Soil moisture sensor for garden/greenhouse, solar tracker etc.

• MQTT Dash : https://play.google.com/store/apps/details?id=net.routix.mqttdash&hl=en_US (preffered). basic javascript automation possible with this App. See https://github.com/ByTE1974/byte1974.github.io/tree/master/mqttdash/js
• MQTT Explorer : https://github.com/thomasnordquist/MQTT-Explorer
• Node-Red : It is also possible to run Node-Red on android smartphones or tablets. https://nodered.org/docs/getting-started/android

• https://github.com/G6EJD/Processor-Solar-Power-Sleep-Calc
• http://www.of-things.de/battery-life-calculator.php
• Very informative discussion on energy harvesting: https://forum.mysensors.org/topic/10812/the-harvester-ultimate-power-supply-for-the-raybeacon-dk/105?lang=en-US
• Interesting paper describing Batteryless remote sensor device: https://arxiv.org/pdf/1505.06815.pdf
• In depth energy harvesting video at Dave Jones: https://www.youtube.com/watch?v=9aSPopIcKLQ

• https://ayushsharma82.github.io/file2raw/
• https://gchq.github.io/CyberChef/#recipe=Gzip('Dynamic%20Huffman%20Coding','index.html.gz','',false)To_Hex('0x',0)Split('0x',',0x')&input=PGh0bWw%2BC

This project was possible thanks to creators of following libraries used for this project:

• https://github.com/hsaturn/TinyMqtt
• https://github.com/leeoniya/uPlot
• https://github.com/me-no-dev/ESPAsyncWebServer