Comments (13)
I have the same or similiar issue. I can't get the GUI software to work on v48
and Arduino wont upload any of the firmware or a bootloader. HELP!
Original comment by [email protected]
on 6 May 2013 at 8:55
from brushless-gimbal.
Its' possible you may have v46 flashed to your controller card. I found that
the new USB driver from FTDI is not compatible with some v46 flashed cards on
some Windows XP systems. Delete the FTDI Driver version 2.08.28 on your
computer. Load previous version 2.08.24 from
http://www.ftdichip.com/Drivers/VCP.htm website on to your computer. They have
an executable file if you need. Now open Arduino, with the v48.ino and flash
the new firmware to you card. You are now ready to program with the latest v48
GUI.
Original comment by [email protected]
on 8 May 2013 at 6:27
from brushless-gimbal.
I have same issue , I have changed FTDI driver to previous version 2.08.24 ,
can't solve the issue. HELP!! Thanks....
Original comment by [email protected]
on 13 May 2013 at 2:04
from brushless-gimbal.
I haven't solved it yet, but will report the problem asap!
Virgis
Original comment by [email protected]
on 13 May 2013 at 6:40
from brushless-gimbal.
I assembled 3 pcs of the board ,all of the board are same issue . please help !!
Original comment by [email protected]
on 14 May 2013 at 4:25
Attachments:
from brushless-gimbal.
Any body can help me !! I still can't download firmware from USB.
Original comment by [email protected]
on 17 May 2013 at 9:55
from brushless-gimbal.
I'm using FTDI Driver 2.08.24.0. FTDI Driver 2.08.28.0 does not work for
Arduino or GUI on my XP laptop. Had v48 loaded and and able to change PID
parameters, etc. and saved to board. Downloaded and loaded v49 to board. Now
when I try and change any parameters PID, max PWM, RC-Min, RC- Max for both
Pitch and Roll and click save values from gui into board parameters are not
saved to board, however I do sometimes get the ERROR: error flushing
"filef77a58": permission denied when triying to save GUI setting to board.
Original comment by [email protected]
on 29 May 2013 at 11:07
from brushless-gimbal.
PLEAS HELP ME!!!
i just paid 189 for this from infity hobby and i cant find or open the gui my
gimbal is over driving bad i would pay $$ to any body who could help me or this
is going back in the mail to Infity Hobby! my e mail is [email protected] my
cell is 323-717-5775 thanks im on youtub under awcinema
Original comment by [email protected]
on 6 Jun 2013 at 11:42
from brushless-gimbal.
[deleted comment]
from brushless-gimbal.
To anyone who has issues with connecting to the board, the FTDI driver version
that you should use is 2.8.14.0. You can find it in the windows update archive:
http://catalog.update.microsoft.com/v7/site/ScopedViewRedirect.aspx?updateid=e50
522c1-52bf-4096-b78e-a402eb13294e
good luck
Original comment by [email protected]
on 24 Jun 2013 at 6:25
from brushless-gimbal.
I have just successfully changed the Arduino code and flashed the card...I have
also managed to download the GUI and made that work with the card...founf -46
to be Fully functional whereas some components of v -49 failed to
work....Gimbal is working fine...with some exceptions that the motors do not
hold DURING flight./....works fine on ground...have tied shock mounting the
gnbal ut it just constantly drives the tilt .... Question...DOES the BOARD have
part of the IMU on it and DOES the bard have to be Horizontal and in Line with
the gimbal...
Original comment by [email protected]
on 24 Jul 2013 at 6:42
from brushless-gimbal.
I just manage to download firmware
choose from arduino "Arduino mini w/ ATmega 328" no 5V version
programmer "AVRRISP mkII"
Original comment by [email protected]
on 1 Aug 2013 at 1:24
from brushless-gimbal.
I have programmed but if I remove the board from my computer.
board does not work and the green light flashes quickly
Original comment by [email protected]
on 19 Nov 2013 at 1:19
from brushless-gimbal.
Related Issues (20)
- MPU drift
- v0.49 r69, GUI will no longer read values from the board and cannot flash back to earlier firmware. HOT 2
- No PID tuning guide - Wiki needed HOT 6
- No COM port is found
- 'InitIMU' was not delcared in the scope
- Settings not restored from file HOT 3
- Motor 1 channel have some voltage even all PID & PWN% are 0. HOT 2
- MPU LPF
- can't write rc-channel in ppm-mode heigher than 3 in controller (r179) HOT 1
- GUI coding issue HOT 2
- Change request/nice to have - BLG tool/Waveform scope/display gyro signal too
- Motor twitching HOT 1
- License violation
- No Level With Rotation (Yaw) with Pitch Tilted Down HOT 6
- pitch does not respond correctly...
- Can not pitch 90 degrees down - Roll axis goes crazy HOT 5
- NEW FIRMWARE ALPHA Version 049 r40 incl. GUI HOT 4
- NEW FIRMWARE Version 049 r45. Using GUI 48. Pitch Control HOT 6
- Firmware 048 r58 unusable HOT 2
- Wrong centering on pitch adjustment from RC and other minor motor problem HOT 3
Recommend Projects
-
React
A declarative, efficient, and flexible JavaScript library for building user interfaces.
-
Vue.js
🖖 Vue.js is a progressive, incrementally-adoptable JavaScript framework for building UI on the web.
-
Typescript
TypeScript is a superset of JavaScript that compiles to clean JavaScript output.
-
TensorFlow
An Open Source Machine Learning Framework for Everyone
-
Django
The Web framework for perfectionists with deadlines.
-
Laravel
A PHP framework for web artisans
-
D3
Bring data to life with SVG, Canvas and HTML. 📊📈🎉
-
Recommend Topics
-
javascript
JavaScript (JS) is a lightweight interpreted programming language with first-class functions.
-
web
Some thing interesting about web. New door for the world.
-
server
A server is a program made to process requests and deliver data to clients.
-
Machine learning
Machine learning is a way of modeling and interpreting data that allows a piece of software to respond intelligently.
-
Visualization
Some thing interesting about visualization, use data art
-
Game
Some thing interesting about game, make everyone happy.
Recommend Org
-
Facebook
We are working to build community through open source technology. NB: members must have two-factor auth.
-
Microsoft
Open source projects and samples from Microsoft.
-
Google
Google ❤️ Open Source for everyone.
-
Alibaba
Alibaba Open Source for everyone
-
D3
Data-Driven Documents codes.
-
Tencent
China tencent open source team.
from brushless-gimbal.