RASPTENDO Case is an SNES inspired enclosure for your Raspberry Pi 3. Esthetically, the case seamlessly aligns with the retro themed RetroPie game station OS. The RASPTENDO case includes a built-in POWER and RESET buttons, and a Status LED to signal power status. The section below provides a step by step guide on how to make it work.

The RASPTENDO POWER button safely switches off your Raspberry Pi 3 to avoid corrupting your SD card when you cut off the power supply. The button is programmed to be held for a second before executing the shutdown command to prevent accidental power off.

There are two ways you can mod the RASPTENDO RESET button, one for soft reboot and one for hard reset. For more information about choosing the right mod for you, please visit this page.

To install the software for your Rasptendo you can choose from the following options.

Option 1: Executing a one line bash script in the terminal

Option 2: Editing configuration files and running a python script on startup in the terminal

Option 1 is the simplest way to install necessary software for your Rasptendo case. The script automatically configures your RetroPie for the Rasptendo buttons to work.

1. RetroPie

   To install Retropie you may download the image for Raspberry Pi 3 and follow installation instruction at the Argon40 website.

2. Internet connection

   To set up your internet via WiFi, you can follow instructions here.

3. Keyboard and screen, or any computer/laptop (via SSH)

   To access your Pi via SSH, you can also follow instructions here.

4. Rasptendo SNES Case

   You may purchase from the link here.

(NOTE: This assumes that you have already connected the jumper wires to the correct PINS and ports. It's very important to follow the right pin configuration to prevent damage to your Pi. If you haven't, you can follow the instructions here.)

This instruction is a step-by-step guide to install necessary software for your RASPTENDO Case. You can setup this via SSH or using the command line interface in your RetroPie. To enter the command line interface of RetroPie, PRESS F4 just after booting up.

Open your terminal and type the one-line installation command below:

$ wget -O - "https://raw.githubusercontent.com/Argon40Tech/Super-Rasptendo-Case-Power-Switch/master/install.sh" | sudo bash

The script will automatically install pertinent files and configure your Raspberry Pi to enable RASPTENDO POWER Button. Installation will automatically reboot once all processes are completed.

After rebooting, your RASPTENDO Case Buttons are now fully functional. To test if your buttons work, try holding the POWER button. The status LED should start blinking and if you held the button for a second, your Raspberry Pi should shutdown. To "wake" it up, you can press the POWER button again.

Open your terminal and follow instructions below.

The Status LED should be connected to the GPIO 14 or PIN 8 serial port so make sure it is enabled. In your terminal, type:

$ sudo nano /boot/config.txt

Check if UART is already enabled by searching for a line at the config.txt with

enable_uart=1

if it's not, add that line at the bottom. Save the file by typing CTRL + X, hit Y, then Enter.

Type

$ sudo apt-get update

to make sure your list of packages and PPA's is up to date.

In order for the POWER button to work, you have to install GPIOZero.

$ sudo apt-get install python3-gpiozero

If you want to know more about GPIOZero, you can read the official documentation.

Change to the /opt/ directory

$ cd /opt/

and create a directory for the script,

$ sudo mkdir Rasptendo

Change to the newly created directory and download the python script using wget.

$ cd /opt/Rasptendo
$ wget "https://raw.githubusercontent.com/Argon40Tech/Super-Rasptendo-Case-Power-Switch/master/halt_wake.py"

In order for the script to run on every boot up, you have to add a command in /etc/rc.local.

$ sudo nano /etc/rc.local

Before the line,

exit 0

add the following command,

sudo python3 /opt/Rasptendo/halt_wake.py

Save the file by typing CTRL + X, hit Y, then Enter.

$ sudo reboot

After rebooting, your RASPTENDO Case Buttons are now fully functional. To test if your buttons work, try holding the POWER button. The status LED should start blinking and if you held the button for a second, your Raspberry Pi should shutdown. To "wake" it up, you can press the POWER button again.

[1]: Wake from halt