T5-4.7 Plus S3 hardware issues & partial clear corruption about lilygo-epd47 HOT 12 OPEN

VCOM is the common voltage of the Eink display, the potentiometer is connected to R10, which is connected to -15V. I do not know the resistance of the potentiometer(U4 in the schematic), but it creates a voltage divider, so the output voltage can be adjusted from 0V(GND) and a negative value. The opamp buffers this voltage as the screen will draw more current than a voltage divider can supply without being affected.

If you use a screwdriver and turn the potentiometer slightly, the voltage you measure on pins 2 and 5 will change. Just make sure that the display's power converters are on or the measured voltage will not be correct.

from lilygo-epd47.

@AdriVerhoef Thank you very much for sharing!

Could you please provide more close-up photos, what exactly did you solder to silence the board?

from lilygo-epd47.

Mods:

• Orange: 2x 22uF + 1x47uF, but as stated earlier, that didn't improve the ripple voltage as the oscillation was already resolved.
• Red: The connections of the opamps as indicated in the first post to create a voltage follower/unity gain configuration. Added a 100nF to buffer the VCOM voltage from the potentiometer.
• Calibrated the VCOM voltage to -1.1V
• Dark Green: Added an additional 1uF to the positive output of the symmetrical boost converter
• Purple: Changed the pull-ups on the enable from 100k to 10k, since the voltage on those pins was not stable due to the high resistance of the original resistors and the input current of the inputs.

Mods:
Cut the trace at the green line and scrape the solder mask from the trace, so the resistor can be soldered. For the buffer capacitor the ground plane needs to be solderable, so remove the soldermask at an appropriate distance from the trace.

So do you have similarly problems with the board? Noise and ghosting?

I've also discovered that the STR_IO0 signal is connected to two pins on the ESP32S3. Would have been nice if the STR and IO0 functionality had been separated, so the shift register and push-button where not connected. However the connecting trace seems to be under the ESP32S3 module or on the other side of the board below the adhesive.

from lilygo-epd47.

@AdriVerhoef Thanks!

So do you have similarly problems with the board? Noise

Noise. Especially when updating the screen. Gone only after epd_poweroff_all();.

I did some modifications already, before your answer. Here they are:

• I connected 2 with 5 on U5 / LM358. Noise goes a bit down.
• I connected 7 with 6 on U5 / LM358. Noise goes a bit down
• I added 2x22pF ceramic capacitors, because they were lying around. Noise goes a bit more down .
• I finally added 47uF electrolytic capacitor (lying around as well). Noise gone completely.
• ADDED EDIT: I could then unsolder 2x22pF, but decided to leave them as is.

By the way, your images show connection between 3 and 5, is this intentional? Or did I mix things up?

I connected all these without any idea what I'm doing (except maybe that I'm filtering some pulsations). No idea about opamps as well. Noise gone.

Are my modifications safe for the screen?

I don't own an oscilloscope, but I measured a couple of voltages, here they are:

from lilygo-epd47.

I see I've connected pin 2 in my example of the schematics and pin 3 on my board. It doesn't really matter, the second opamp is now in series with the first, whereas on my board both opamp inputs are connected to the potentiometer.

Just ensure that the leads of your capacitors do not make contact with the rest of the circuit and you should be fine. The 22pF don't do much, but won't harm either. The 47uF is 47000000pF so that adds the missing capacitance the +15V regulator requires, as it is oscillating when the screen is updating.
You do need to reduce the VCOM voltage by turning the potentiometer, the voltage should be around -1.1V ~ -1.3V. When this is reduced, the screen corruption during a partial clear and draw is significantly reduced. However I've programmed my board with the weather example which updates the screen fully, as I still found it too visible.

from lilygo-epd47.

@AdriVerhoef Thanks!

Yep, I double-checked that there are no solder traces left, and the capacitors remain isolated.

You do need to reduce the VCOM voltage by turning the potentiometer, the voltage should be around -1.1V ~ -1.3V.

Is VCOM a voltage between 3 and GND? Sorry for the dumb question

from lilygo-epd47.

@AdriVerhoef And one more question - did you find any issues with RTC?

Mine resets to zeros every time I reboot the board. Is it intended? Does your work the same?

from lilygo-epd47.

I have not tested the RTC, since I'm not using it. Sounds like the back-up battery does not hold any charge or your code might reset the device on initialization. Have you measured if the battery voltage is ok?

from lilygo-epd47.

@AdriVerhoef The battery shows 2.66V between its PCB pins.

As far as I know, I don't reset the RTC intentionally. I've skimmed through https://github.com/lewisxhe/PCF8563_Library/tree/master/src , but did not find any code that resets it during initialization.

from lilygo-epd47.

I've just bought this board with the display and EVERYTHING you describe is completely true in my case as well (S3 version): the noise, the partial grayout etc.
I think that goes without saying: "you pretend to pay me - I pretend to be a good board" - eh...

btw when you power this board using the BAT connector, when. you enter epd_poweroff_all() it still draws about 270uA that is way too much - if I am going to use this board I would add some circuit to disconnect the power completely and only turn ON periodically (i.e. every 3min or so)

on top of that, the library provided by Lilygo is full of errors - I am wondering if other libraries would work, i.e. TFT_eSPI - that would be amazing

from lilygo-epd47.

Some comments after using the board for a bit (under micropython):

• the button STR_IO0 is essentially not usable as it is used for the epaper control signals (via the shift reg) -> if you try to use it as a general button then the epaper updates don't work... I'm thinking about cutting the trace and wiring the button to a different IO to be able to use it for the application
• bizarrely I can't get the button IO inputs to generate an IRQ (using micropython, but the code works on other ESP32S3 boards...)
• 50% of the the time when I start the epaper driver, the board browns out (powered by USB) and resets -> I need to try some of your 'add caps' fixes
• epaper driver code is somewhat buggy, specially for partial updates -> need to fix that code for the last line writiing
• power consumption : not fab, I suspect because the buck-boost for the epaper has no way to control its 'shutdown' input
• for the micropython command line, I ended up soldering a header to the GND/RX/TX on the 40 way header to access the UART, instead of using the native USB uart -> doesn't disconnect from the PC at every reset, and lets you see the reboot logs (this is how I saw the brownout reset for example)

definitely feels like a friday afternoon design...

from lilygo-epd47.

update:

• button IRQ : use esp-idf-4.4.1 or later, there is a bug for the ESP32S3 in 4.4
• epaper driver : in need of debug/refactoring to seperate versions for ESP32 / ESP32S3 as they use a different lib to transfer the data (I2S on ESP32, esplcd on ESP32S3)?

from lilygo-epd47.