Comments (7)
Are you looking for the diybms to be a slave to the charger/inverter? Will it have to answer questions or will it be transmitting to them?
from diybmsv4esp32.
Only transmit information.
So master :-)
BMS = Battery Management System.
We can't have two captains on one ship!!
It's a valid question, as CAN is 2 way protocol.
It could have been so simple.
Apparently the Chinese designer of the hybrid inverter / battery pack wanted to look extra smart by using only CAN...
Or actually, if I understood it correctly, they where already selling 5 kWh LiFePO4 battery packs, S15 and used that system as guideline for BMS/LiFePO4....
What just happened to be CAN
Their standard LiFePO4 settings is for S15 only..
And where flabbergasted when I told them S16 is more or less industry standard.
Obtainium, without market research..
Can bite you in the @ss
In my situation, the hybrid inverter has absolutely nothing to tell to the BMS, as I don't want the BMS to be configured via the inverter.
(We got the nice web interface)
What I hope will happen is that the MPPT charge will automatically be adjusted when it receives more accurate information about individual cell voltages, and not just pack voltage.
The voltage shown isn't accurate, it shows 52 when the cells are 53, but the difference is always the same, so easy to adjust the (manual) charging protocol to correct this voltage offset.
Perhaps in the future if the smart shunt is implemented, it can give more accurate information about battery usage.
That would be nice.
Thank you!!
from diybmsv4esp32.
foxBMS/foxbms-1#3 CAN discussion and many specs linked
from diybmsv4esp32.
@fhorst1 what brand are these inverters? Do you have a link to the supplier/shop?
The BMS should be able to easily transmit those CAN messages, its very similar to the Victron protocols.
from diybmsv4esp32.
Brand name is "Sorotec"
Type Revo II
http://www.sorotecups.com/product-detail/on-grid-off-grid-hybrid-inverter/
It's a nice one, price quality wise.
Not Victron, also not Victron price.
Energy conversion is good and "clean" Mppt max is 4500 watt, their information of 5500 is incorrect.
Even with 8000 watt of possible solar.... Stuck at 4500w :-)
Different story.
I need to build my own mppt that's capable of higer voltage (350-400v) and higher capacity (7500-12500W) on 51.2 LiFePO4.
Perhaps you know about a development?
Anyway...
The information earlier provided for the CAN, I don't know if it's a standard with all information in the same location, of its anarchy....
December time to update the project, I'll see if it can talk now CAN is activated in de firmware.
Thank you.
from diybmsv4esp32.
diyBMS won't be sending the right messages to your inverter, even though its CAN enabled.
You may actually cause problems, because the CAN-ID's overlap with Victron, so you may get garbage (or worse) received by the inverter.
from diybmsv4esp32.
No update on this issue since 2021, so going to close, please re-open if needed.
from diybmsv4esp32.
Related Issues (20)
- Cell Voltage reading freaks out when Active Balancer kicks in - STM32All-In-One HOT 7
- Temperature display 16S balancer HOT 5
- Suggestion improve Cell runaway function HOT 6
- WIFI Issue - random reboot when STA is lost (investigation) HOT 31
- Identifying which battery bank I am looking or working on? HOT 1
- CVL and Venus bug HOT 3
- Loosing wifi on reboot from 5v board power but not usb HOT 8
- Dynamic Charging HOT 4
- Use 16 Cell chip but change script to 12 Cell HOT 5
- Randomly disabling relay when battery is almost to the top, no rules seem to be afected. HOT 8
- Possible to send 'wrong' voltage info over the CANBUS to inverter ? HOT 1
- Possible to send 'wrong' voltage info over the CANBUS to inverter ? HOT 6
- Shunt Voltages over 40.96mV can't be measured when using internal shunt HOT 2
- V490 AiO JLC replacements for C20, D1, U2, U3
- CAN - Failed to queue CANBUS message (chip=TJA1057GT/3J) HOT 14
- Controller restart when saving config to SD card HOT 3
- Upload Config but Failed to save settings HOT 13
- Discharge also a curve for amps go down HOT 2
- Emergency Stop
- Displayed power is not correct HOT 6
Recommend Projects
-
React
A declarative, efficient, and flexible JavaScript library for building user interfaces.
-
Vue.js
🖖 Vue.js is a progressive, incrementally-adoptable JavaScript framework for building UI on the web.
-
Typescript
TypeScript is a superset of JavaScript that compiles to clean JavaScript output.
-
TensorFlow
An Open Source Machine Learning Framework for Everyone
-
Django
The Web framework for perfectionists with deadlines.
-
Laravel
A PHP framework for web artisans
-
D3
Bring data to life with SVG, Canvas and HTML. 📊📈🎉
-
Recommend Topics
-
javascript
JavaScript (JS) is a lightweight interpreted programming language with first-class functions.
-
web
Some thing interesting about web. New door for the world.
-
server
A server is a program made to process requests and deliver data to clients.
-
Machine learning
Machine learning is a way of modeling and interpreting data that allows a piece of software to respond intelligently.
-
Visualization
Some thing interesting about visualization, use data art
-
Game
Some thing interesting about game, make everyone happy.
Recommend Org
-
Facebook
We are working to build community through open source technology. NB: members must have two-factor auth.
-
Microsoft
Open source projects and samples from Microsoft.
-
Google
Google ❤️ Open Source for everyone.
-
Alibaba
Alibaba Open Source for everyone
-
D3
Data-Driven Documents codes.
-
Tencent
China tencent open source team.
from diybmsv4esp32.