Comments (21)
QC cant do 28V (Spec only goes to 20V); so what is likely happening is that the PD profile is "stuck" and so therefore PD negotation fails and we assume its QC.
To force QC you set PD timeout to 0
from ironos.
Thank you for your quick reply.
I tried setting the PD timeout to OFF (0 not selectable, lowest is 1 on my build) with no apparent effect.
The TS101 still cycles through the voltages from 5 to 28 displaying PD 28.6V in the end with the same problem occurring.
If it sporadically ends up displaying QC with 28V it functions as intended pulling peaks of 80-100W as indicated on the iron as well as on the powerbank. So it seems to utilize the full 28V even though it assumes itΒ΄s on QC mode.
Any advice on how to investigate this problem further?
from ironos.
Any advice on how to investigate this problem further?
Absolute best step is to get a capture of the USB-PD packets being exchanged to debug what is going on.
otherwise next best is to boot up the iron holding the rear button to start the PD debug menu that should show what options your power supply is advertising, and make sure all advertised options match the label.
This will also show a state number that can be used to trace where its getting to in negotiating USB-PD
from ironos.
Unfortunately tracking the PD packets is out of reach for my expertise and equipment.
The PD-Debug Menu seems to show nohing unexpected either. Maybe you can spot something strange:
After negotiating it shows the following in the PD-Debug menu:
State 12 No VBus
1 5V 3.00A
2 9V 3.00A
3 12V 3.00A
4 15V 3.00A
5 20V 5.00A
6 3-21V 5.00A
8 28V 5.00A
Only thing odd is that that the "State 12 No VBus" display flickers every 5-10sec, and displays "State 2 No VBus" for a fraction of a second (litterally 1/10th of a second) before rerutning to State 12.
Something else i discovered is that starting to heat immediately after plugging in the Iron, greatly increases my chances of it functioning "normally" while displaying the odd QC 28V. It seems that starting to preheat before PD is finished negotiating greatly improves the chance of working.
Also note that it only shuts off and reboots while heating. Also the power pulse can trigger the reboot if set too high (i lowered it to mitigate that problem)
Any further advice?
from ironos.
I have a newly purchased TS101 (90W). I am experiencing similar symptom of iron rebooting while heating up on 140W Apple PD3.1 brick with EPR lead in 28v mode. This happens with V2.22, I haven't tried older firmware.
If I try another apple brick that only does 20v 5A, issue does not reproduce.
Issue also does NOT reproduce using stock firmware.
from ironos.
Related Issues (20)
- Add support for GDCPH 65W USB PD hot plate HOT 2
- Pinecil v2 doesn't boot on Baseus Blade 100w 20 000 mAh HOT 2
- What should I do to avoid sudden temperature spikes on the screen? HOT 1
- compilation error Pinecilv2 help HOT 3
- pinecilv2 Bootup Logo not showing HOT 3
- how many measurements does the ADC make between PWM pulses? HOT 5
- questions about the code HOT 3
- TS101: How to switch back to the stock Firmware HOT 5
- Using 18v DC input reboots PinecilV2 when starting to heat HOT 7
- mhp30 no PD stuck in QC HOT 2
- New MHP30 [Hver:1.60] troubles. HOT 1
- Animated Boot Logo. Continuously repeat animation when boot logo duration is set to infinity. HOT 8
- Quecoo T85 96w HOT 11
- PTS-200 support HOT 2
- pts200 tip for ts101 HOT 9
- MHP30 Lower minimum temperature than 100C? HOT 6
- TS80P screen orientation upside down HOT 12
- Pinecil V2 won't switch to 20V on 5v/20v only capable powerbank HOT 6
- Disable Bluetooth by default to minimize attack vectors HOT 5
Recommend Projects
-
React
A declarative, efficient, and flexible JavaScript library for building user interfaces.
-
Vue.js
π Vue.js is a progressive, incrementally-adoptable JavaScript framework for building UI on the web.
-
Typescript
TypeScript is a superset of JavaScript that compiles to clean JavaScript output.
-
TensorFlow
An Open Source Machine Learning Framework for Everyone
-
Django
The Web framework for perfectionists with deadlines.
-
Laravel
A PHP framework for web artisans
-
D3
Bring data to life with SVG, Canvas and HTML. πππ
-
Recommend Topics
-
javascript
JavaScript (JS) is a lightweight interpreted programming language with first-class functions.
-
web
Some thing interesting about web. New door for the world.
-
server
A server is a program made to process requests and deliver data to clients.
-
Machine learning
Machine learning is a way of modeling and interpreting data that allows a piece of software to respond intelligently.
-
Visualization
Some thing interesting about visualization, use data art
-
Game
Some thing interesting about game, make everyone happy.
Recommend Org
-
Facebook
We are working to build community through open source technology. NB: members must have two-factor auth.
-
Microsoft
Open source projects and samples from Microsoft.
-
Google
Google β€οΈ Open Source for everyone.
-
Alibaba
Alibaba Open Source for everyone
-
D3
Data-Driven Documents codes.
-
Tencent
China tencent open source team.
from ironos.