Everything working - Yes for manual focus
Pi model - 3b
used cameras - Arducam 16mp AF

updates needed to enable
/boot/config.txt
dtoverlay=vc4-kms-v3d,cma-128
gpu_mem=128 # preferred 160 or 256MB
dtoverlay=imx519

/boot/camera-streamer/libcamera.conf
hash out/delete the line - --camera-options="AfMode=2" --camera-options="AfRange=2"

from octopi-uptodate.

Installed on an RPi 4B with an RPi camera V3. Updated to 1.9.0rc5 successfully. Some strangeness with the camera view on the Control tab that I need to investigate more carefully.

from octopi-uptodate.

After investigating more carefully, the camera view issue has been resolved. It may have been operator error regarding the hflip and vflip checkboxes due to the fact that they moved from the Webcam & Timelapse settings on 1.8.7 to the Classic Webcam plugin settings on 1.9.0rc5.

from octopi-uptodate.

Installed on both my test system (Pi4B 4GB + RasPi CamV3 +HyperPixel 4 rectangle) and my main system (Pi4B 2GB + RasPi CamV3 +HyperPixel 4 square)
Initially, the Wifi would not connect when the image had finished loading up. I was able to use raspi-config to set up the WiFi data again and it worked. I used RasPi Imager V1.7.4 on my Windows 11 PC. I did not get the same problem when using the MacBook Pro version to create the SD card.

Everything working?
Working perfectly and I was able to restore my backup without any issues.

Pi model + used cameras
Pi4B 4GB + RasPi CamV3 +HyperPixel 4 rectangle
Pi4B 2GB + RasPi CamV3 +HyperPixel 4 square

Ruhel™

from octopi-uptodate.

Everything working - Not OOTB if you want Autofocus
Pi model - 3b
used cameras - Arducam 16mp AF
in case of issues: https://paste.octoprint.org/GQJEZqcI5Z

• Didnt work OOTB as no camera found
• I installed the drivers from arducam site and get a postive from Libcamera-hello and v4l2-ctl --list-devices but no joy in octopi
• I recompiled camera streamer using the instructuiuons on ayufans site and it itt reported "May 07 12:52:39 octopi sh[1203]: /bin/sh: 1: exec: /usr/bin/camera-streamer: not found " though I could see its installed camera streamer in /usr/local/bin
• I set a symbolic link from /usr/bin/ to /user/local/bin/camera-streamer and its now working

Did i do anything weird?

Update: Arducam confirmed that the AF updates to libcamera are not planned to be upstreamed to pi/libcamera anytime soon

They so confirmed the install of their libcamera removed camera-streamer so the recompile/symlink looks like it's needed for AF to function.

from octopi-uptodate.

@flipside101 recompiling camera-streamer pretty much nuked the whole test I fear. The goal here is to figure out if stuff on the image works as it is, so if you start replacing parts with custom builds, especially the core of the camera stack that this is all about, it's a bit unhelpful 😅

In any case, from the looks of it the current version on the master branch of camera-streamer is still the very same that's packaged up here and installed on the image, and from the looks of your logs, that version started up fine on May 7th at 14:29, but earlier indeed the binary seems to have gotten lost, possibly due to your recompile?

For comparison, this is from a fresh flash of the image, with an RPiCam v3 module:

pi@octopib:~ $ cat /etc/octopiuptodate_build 
1.0.0-1.8.7-20230504122418
pi@octopib:~ $ which camera-streamer
/usr/bin/camera-streamer
pi@octopib:~ $ camera-streamer --version
v0.1-21-g54f538e (54f538e)
pi@octopib:~ $ dpkg -L camera-streamer
/.
/usr
/usr/bin
/usr/bin/camera-streamer

The binary is sitting where it's expected, /usr/bin/camera-streamer, and that's also where it got installed to by the aforementioned debian package.

from octopi-uptodate.

@foosel
Hi The earlier logs are before the recompile, though after the arducam driver install. The May 7th logs are after the recompile and sym link

I'll restart again and document the steps better but as i said it didn't seem to work OOTB even with the drivers installed and dtoverlay entry whilst I good get a picture off the camera and all the needed devices looked to be working it was only after recompiling camera-streamer that it worked. Oh and I only thought about doing that as it was suggested in an earlier post by ayufan with ref to using teh AF https://github.com/OctoPrint/OctoPi-UpToDate/issues/2#issuecomment-1486638369

from octopi-uptodate.

@flipside101, Didn't you post that the camera is an Arducam 16mp AF? @foosel's reply referenced the RPi camera V3. Are there are extra steps involved to get the Arducam working?

from octopi-uptodate.

@b-morgan I believe so yes and ive listed them in the discussion thread- https://community.octoprint.org/t/discussing-the-new-camera-streamer-based-webcam-stack-for-octopi-currently-in-development/50866/25. Im going to restest and ill document there so not to clog up here.

from octopi-uptodate.

Not sure if this is relevant feedback as the camera itself seems to be working just fine, but I thought I'd share regardless.

• Everything working?

  • Camera stream itself works.
  • As long as the camera is connected/enabled, communication issues between the Pi and the MCU arise intermittently. Firmware used is Klipper, Klipper's logs show this error: MCU 'mcu' shutdown: Timer too close. The issue has been appearing regardless of whether the printer was currently printing or idling at the time and seems to have disappeared after disabling and disconnecting the camera.

• Pi model:

  • Raspberry Pi Zero 2 W

• Camera used:

  • Raspberry Pi Camera Module 3 (Wide)

• Related logs

  • https://paste.octoprint.org/cHHk00VtMf

  • May 11 13:36:47 voronpi octoprint[2440]: 2023-05-11 13:36:47,521 - octoprint.util.comm - WARNING - Received an error from the printer's firmware: MCU 'mcu' shutdown: Timer too close
    May 11 13:36:47 voronpi octoprint[2440]: | Last lines in terminal:
    May 11 13:36:47 voronpi octoprint[2440]: | Recv: ok B:69.3 /110.0 T0:45.3 /235.0
    May 11 13:36:47 voronpi octoprint[2440]: | Send: M105
    May 11 13:36:47 voronpi octoprint[2440]: | Recv: ok B:69.3 /110.0 T0:45.2 /235.0
    May 11 13:36:47 voronpi octoprint[2440]: | Send: M105
    May 11 13:36:47 voronpi octoprint[2440]: | Recv: ok B:69.2 /110.0 T0:45.2 /235.0
    May 11 13:36:47 voronpi octoprint[2440]: | Send: M105
    May 11 13:36:47 voronpi octoprint[2440]: | Recv: ok B:69.1 /110.0 T0:45.1 /235.0
    May 11 13:36:47 voronpi octoprint[2440]: | Send: M105
    May 11 13:36:47 voronpi octoprint[2440]: | Recv: ok B:69.0 /110.0 T0:45.1 /235.0
    May 11 13:36:47 voronpi octoprint[2440]: | Send: M104 S235
    May 11 13:36:47 voronpi octoprint[2440]: | Recv: // MCU 'mcu' shutdown: Timer too close
    May 11 13:36:47 voronpi octoprint[2440]: | Recv: // This often indicates the host computer is overloaded. Check
    May 11 13:36:47 voronpi octoprint[2440]: | Recv: // for other processes consuming excessive CPU time, high swap
    May 11 13:36:47 voronpi octoprint[2440]: | Recv: // usage, disk errors, overheating, unstable voltage, or
    May 11 13:36:47 voronpi octoprint[2440]: | Recv: // similar system problems on the host computer.
    May 11 13:36:47 voronpi octoprint[2440]: | Recv: // Once the underlying issue is corrected, use the
    May 11 13:36:47 voronpi octoprint[2440]: | Recv: // "FIRMWARE_RESTART" command to reset the firmware, reload the
    May 11 13:36:47 voronpi octoprint[2440]: | Recv: // config, and restart the host software.
    May 11 13:36:47 voronpi octoprint[2440]: | Recv: // Printer is shutdown
    May 11 13:36:47 voronpi octoprint[2440]: | Recv: !! MCU 'mcu' shutdown: Timer too close
    

from octopi-uptodate.

Everything working: yes
Pi Pi4B 4GB
RaspiCam V3 AF
Was on 1.9.0rc6 before, made backup, then fresh install including setup, upgraded back to 1.9.0rc6, restored backup, everything still ok, camera working, including AF.

from octopi-uptodate.

This issue has been mentioned on OctoPrint Community Forum. There might be relevant details there:

https://community.octoprint.org/t/discussing-the-new-camera-streamer-based-webcam-stack-for-octopi-currently-in-development/50866/31

from octopi-uptodate.

Everything working: seems to work fine on first tests.
Model: Raspberry Pi 3 Model B Plus Rev 1.3
Camera 1: Raspberry Pi V2.1, 8 MP 1080P Camera-Modul
Camera 2: Creative Technology Ltd / Live Cam Sync HD VF0770

Setup:

• Blank flash/install, no backup used
• sudo remove-usb-camera default, sudo add-usb-camera livecamsynchd (as suggested in the docs)
• Additionaly (maybe add to docs): edited haproxy.cfg to add a webcam2 path for the second cam.
• installed MultiCam plugin and configured usb camera using webcam2 path / port 8081

from octopi-uptodate.

Everything working?
No, I did the two steps described by @flipside101

in /boot/config.txt I put:
[all]
dtoverlay=vc4-kms-v3d,cma-128
gpu_mem=128 # preferred 160 or 256MB
dtoverlay=imx519

and in /boot/camera-streamer/libcamera.conf I uncommented:
#OPTIONS='--camera-options="AfMode=2" --camera-options="AfRange=2"'

Octoprint says: "Webcam Stream not loaded"
There is no camera found in /webcam/?action=stream

Pi model
Pi 3b+

used cameras
Arducam 16MP AF IMX519

Issue log
https://paste.octoprint.org/rmCLvg0N1h)

How do I fix this?
PS: I have been testing many different versions in the last few days and one time (don't remember the version and what steps I did) there was a stream, but it was just a Blackscreen.)

from octopi-uptodate.

You still have AF active so Camera-S treamer isn't starting, you need to hash out the AF lines so they are not active

from octopi-uptodate.

You still have AF active so Camera-S treamer isn't starting, you need to hash out the AF lines so they are not active

This is what my libcamera.conf looks like:

###Options for libcamera based cameras (PiCam, Arducam, ...)

#The port on which the webcam server for the camera should listen on. If you have only
#one camera, leave at 8080. If you have more, change to 8081, 8082, etc. The primary
#camera will be considered the one with 8080.
PORT=8080

#The resolution to request on the camera sensor. Defaults to 1280x720.
WIDTH=1920
HEIGHT=1080

#The height to use for the video stream. Defaults to 720.
VIDEO_HEIGHT=720

#The height to use for the snapshots. Defaults to 1080.
SNAPSHOT_HEIGHT=1080

#The framerate to set on the camera. Defaults to 15fps.
FRAMERATE=15

#Additional options. By default enables continuous auto focus (if possible).
#OPTIONS='--camera-options="AfMode=2" --camera-options="AfRange=2"'

What do I need to change?

from octopi-uptodate.

Just to confirm, the instructions from @flipside101 work for me on a Pi4 and an Arducam 16MP AF with manual focus.

from octopi-uptodate.

Just to confirm, the instructions from @flipside101 work for me on a Pi4 and an Arducam 16MP AF with manual focus.

What am I doing wrong?

from octopi-uptodate.

In case you removed the "#" from the second line, you need to put it back and reboot.
#Additional options. By default enables continuous auto focus (if possible).
#OPTIONS='--camera-options="AfMode=2" --camera-options="AfRange=2"'

from octopi-uptodate.

To clarify, this is in another file, not /boot/config.txt, but /boot/camera-streamer/libcamera.conf

from octopi-uptodate.

To clarify, this is in another file, not /boot/config.txt, but /boot/camera-streamer/libcamera.conf

In the /boot/config.txt I put the stuff in, and /boot/camera-streamer/libcamera.conf I uncommented it.

from octopi-uptodate.

Uncommenting is removing the "#", adding a "#" in front of a line is called making the line a comment.
In short, the line must start with a # , everything after that character is ignored by the Pi.

from octopi-uptodate.

Uncommenting is removing the "#", adding a "#" in front of a line is called making the line a comment. In short, the line must start with a # , everything after that character is ignored by the Pi.

It worked!!!! I think I didn't write it out properly. It's still a little slow, can I change the fps somehow?

from octopi-uptodate.

#The framerate to set on the camera. Defaults to 15fps.
FRAMERATE=15
Change that value, but this could be too much for your connection or your Pi at 25

from octopi-uptodate.

#The framerate to set on the camera. Defaults to 15fps. FRAMERATE=15 Change that value, but this could be too much for your connection or your Pi at 25

Does 20 work without issues?
Also can I try and change the video pixels from 720 to 1080?

from octopi-uptodate.

Try and you shall learn! :-)
I did not change these values so far.

from octopi-uptodate.

So, here we go again:

Everything working?

Yes! 🥳🥳

Pi model

Raspberry Pi 3b+

used cameras

16MP Arducam Autofocus IMX 519

Tutorial for everyone who needs it:

To make it work I did these two steps described by @flipside101:
At first SSH into the Pi. If you don't know how, look it up on the internet.

In the root directory of the Pi type:
cd /boot
sudo nano config.txt

Then put the following unter the header "[all]":

dtoverlay=vc4-kms-v3d,cma-128
gpu_mem=128 # preferred 160 or 256MB
dtoverlay=imx519

Write out the file by pressing "Ctrl+O" and then "Enter". You can exit the file with "Ctrl+X".

Next, open the "libcamera.conf" file by pasting the following commands into the terminal:
cd camera-streamer
sudo nano libcamera.conf

Put a "#" in front of the following:

OPTIONS='--camera-options="AfMode=2" --camera-options="AfRange=2"'

Putting a "#" in front of something, makes it a comment. Comments don't get read by the system.
Write out the file by pressing "Ctrl+O" and then "Enter". Exit the file with "Ctrl+X".

In your camera settings in Octoprint you should have:

/webcam/?action=stream

Everything should be working and you should be up and running.

from octopi-uptodate.

Everything working: seems to work fine on first tests. Model: Raspberry Pi 3 Model B Plus Rev 1.3 Camera 1: Raspberry Pi V2.1, 8 MP 1080P Camera-Modul Camera 2: Creative Technology Ltd / Live Cam Sync HD VF0770

Setup:

* Blank flash/install, no backup used

* `sudo remove-usb-camera default`, `sudo add-usb-camera livecamsynchd`  (as  suggested in the docs)

* Additionaly (maybe add to docs): edited `haproxy.cfg` to add a `webcam2` path for the second cam.

* installed `MultiCam` plugin and configured usb camera using `webcam2` path / port 8081

For some reason, the libcamera / PiCam sometimes (I think only after a cold boot) does not come up, either restarting the service or a warm reboot help.

The journalctl (before I restart the service) only logs:

May 23 09:08:07 octopi sh[584]: util/http/http.c: HTTP8080/3: Client connected 127.0.0.1 (fd=5).
May 23 09:08:07 octopi sh[584]: util/http/http.c: HTTP8080/3: Request 'GET' '/' 'action=stream'
May 23 09:08:07 octopi sh[584]: device/links.c: CAMERA:capture: Stale detected. Restarting streaming...
May 23 09:08:07 octopi sh[584]: device/buffer_list.c: CAMERA:capture: Streaming stopped... Was 0 of 2 enqueud
May 23 09:08:07 octopi sh[584]: device/buffer_list.c: CAMERA:capture: Streaming started... Was 0 of 2 enqueud
May 23 09:08:09 octopi sh[584]: util/http/http.c: HTTP8080/3: Client disconnected 127.0.0.1.

After the service restart it logs quite a lot:

May 23 09:09:37 octopi systemd[1]: Stopping camera-streamer libcamera...
May 23 09:09:37 octopi systemd[1]: camera-streamer-libcamera.service: Succeeded.
May 23 09:09:37 octopi systemd[1]: Stopped camera-streamer libcamera.
May 23 09:09:37 octopi systemd[1]: camera-streamer-libcamera.service: Consumed 5.411s CPU time.
May 23 09:09:37 octopi systemd[1]: Starting camera-streamer libcamera...
May 23 09:09:38 octopi sh[1297]: /base/soc/i2c0mux/i2c@1/imx219@10
May 23 09:09:38 octopi systemd[1]: Started camera-streamer libcamera.
May 23 09:09:38 octopi sh[1304]: /usr/bin/camera-streamer Version: v0.1-21-g54f538e (54f538e)
May 23 09:09:38 octopi sh[1304]: [0:28:05.282432363] [1304]  INFO Camera camera_manager.cpp:299 libcamera v0.0.4+22-923f5d70
May 23 09:09:38 octopi sh[1304]: [0:28:05.338273819] [1322]  WARN RPI raspberrypi.cpp:1357 Mismatch between Unicam and CamHelper for embedded data usage!
May 23 09:09:38 octopi sh[1304]: [0:28:05.339588081] [1322]  INFO RPI raspberrypi.cpp:1476 Registered camera /base/soc/i2c0mux/i2c@1/imx219@10 to Unicam dev>
May 23 09:09:38 octopi sh[1304]: device/libcamera/device.cc: CAMERA: Device path=/base/soc/i2c0mux/i2c@1/imx219@10 opened
May 23 09:09:38 octopi sh[1304]: [0:28:05.342351917] [1304]  INFO Camera camera.cpp:1028 configuring streams: (0) 1920x1080-YUYV
May 23 09:09:38 octopi sh[1304]: [0:28:05.342915715] [1322]  INFO RPI raspberrypi.cpp:851 Sensor: /base/soc/i2c0mux/i2c@1/imx219@10 - Selected sensor format>
May 23 09:09:38 octopi sh[1304]: [0:28:05.345941893] [1304]  INFO Camera camera.cpp:1028 configuring streams: (0) 1920x1080-YUYV (1) 1920x1080-SBGGR10_CSI2P
May 23 09:09:38 octopi sh[1304]: [0:28:05.346425744] [1322]  INFO RPI raspberrypi.cpp:851 Sensor: /base/soc/i2c0mux/i2c@1/imx219@10 - Selected sensor format>
May 23 09:09:38 octopi sh[1304]: device/buffer_list.c: CAMERA:capture: Using: 1920x1080/YUYV, buffers=2, bytesperline=3840, sizeimage=0.0MiB
May 23 09:09:38 octopi sh[1304]: device/buffer_list.c: CAMERA:capture: Opened 2 buffers. Memory used: 7.9 MiB
May 23 09:09:38 octopi sh[1304]: device/buffer_list.c: CAMERA:capture:1: Using: 1920x1080/BG10, buffers=2, bytesperline=2400, sizeimage=0.0MiB
May 23 09:09:38 octopi sh[1304]: device/buffer_list.c: CAMERA:capture:1: Opened 2 buffers. Memory used: 4.9 MiB
May 23 09:09:38 octopi sh[1304]: device/v4l2/device.c: SNAPSHOT: Device path=/dev/video31 fd=39 opened
May 23 09:09:38 octopi sh[1304]: device/v4l2/buffer_list.c: SNAPSHOT:output:mplane: Requested resolution=1920x1080 is unavailable. Got 1920x1088.
May 23 09:09:38 octopi sh[1304]: device/buffer_list.c: SNAPSHOT:output:mplane: Using: 1920x1056/YUYV, buffers=2, bytesperline=3840, sizeimage=3.9MiB
May 23 09:09:38 octopi sh[1304]: device/buffer_list.c: SNAPSHOT:output:mplane: Opened 2 buffers. Memory used: 0.0 MiB
May 23 09:09:38 octopi sh[1304]: device/buffer_list.c: SNAPSHOT:capture:mplane: Using: 1920x1056/JPEG, buffers=2, bytesperline=0, sizeimage=4.0MiB
May 23 09:09:38 octopi sh[1304]: device/buffer_list.c: SNAPSHOT:capture:mplane: Opened 2 buffers. Memory used: 8.0 MiB
May 23 09:09:38 octopi sh[1304]: device/v4l2/device.c: RESCALLER:STREAM: Device path=/dev/video12 fd=42 opened
May 23 09:09:38 octopi sh[1304]: device/buffer_list.c: RESCALLER:STREAM:output:mplane: Using: 1920x1080/YUYV, buffers=2, bytesperline=3840, sizeimage=4.0MiB
May 23 09:09:38 octopi sh[1304]: device/buffer_list.c: RESCALLER:STREAM:output:mplane: Opened 2 buffers. Memory used: 0.0 MiB
May 23 09:09:38 octopi sh[1304]: device/buffer_list.c: RESCALLER:STREAM:capture:mplane: Using: 1312x736/YUYV, buffers=2, bytesperline=2624, sizeimage=1.8MiB
May 23 09:09:38 octopi sh[1304]: device/buffer_list.c: RESCALLER:STREAM:capture:mplane: Opened 2 buffers. Memory used: 3.7 MiB
May 23 09:09:38 octopi sh[1304]: device/v4l2/device.c: STREAM: Device path=/dev/video31 fd=45 opened
May 23 09:09:38 octopi sh[1304]: device/buffer_list.c: STREAM:output:mplane: Using: 1312x736/YUYV, buffers=2, bytesperline=2624, sizeimage=1.8MiB
May 23 09:09:38 octopi sh[1304]: device/buffer_list.c: STREAM:output:mplane: Opened 2 buffers. Memory used: 0.0 MiB
May 23 09:09:38 octopi sh[1304]: device/buffer_list.c: STREAM:capture:mplane: Using: 1312x736/JPEG, buffers=2, bytesperline=0, sizeimage=4.0MiB
May 23 09:09:38 octopi sh[1304]: device/buffer_list.c: STREAM:capture:mplane: Opened 2 buffers. Memory used: 8.0 MiB
May 23 09:09:38 octopi sh[1304]: device/v4l2/device.c: VIDEO: Device path=/dev/video11 fd=48 opened
May 23 09:09:38 octopi sh[1304]: device/buffer_list.c: VIDEO:output:mplane: Using: 1312x736/YUYV, buffers=2, bytesperline=2624, sizeimage=1.8MiB
May 23 09:09:38 octopi sh[1304]: device/buffer_list.c: VIDEO:output:mplane: Opened 2 buffers. Memory used: 0.0 MiB
May 23 09:09:38 octopi sh[1304]: device/buffer_list.c: VIDEO:capture:mplane: Using: 1312x736/H264, buffers=2, bytesperline=0, sizeimage=0.8MiB
May 23 09:09:38 octopi sh[1304]: device/buffer_list.c: VIDEO:capture:mplane: Opened 2 buffers. Memory used: 1.5 MiB
May 23 09:09:38 octopi sh[1304]: device/device.c: CAMERA: Setting frame interval_us=0 for FPS=15
May 23 09:09:38 octopi sh[1304]: device/v4l2/device_options.c: SNAPSHOT: Configuring option compressionquality (009d0903) = 80
May 23 09:09:38 octopi sh[1304]: device/v4l2/device_options.c: STREAM: Configuring option compressionquality (009d0903) = 80
May 23 09:09:38 octopi sh[1304]: device/v4l2/device_options.c: VIDEO: Configuring option repeatsequenceheader (009909e2) = 1
May 23 09:09:38 octopi sh[1304]: device/v4l2/device_options.c: VIDEO: Configuring option videobitratemode (009909ce) = 0
May 23 09:09:38 octopi sh[1304]: device/v4l2/device_options.c: VIDEO: Configuring option videobitrate (009909cf) = 2000000
May 23 09:09:38 octopi sh[1304]: device/v4l2/device_options.c: VIDEO: Configuring option repeatsequenceheader (009909e2) = 5000000
May 23 09:09:38 octopi sh[1304]: device/v4l2/device_options.c: VIDEO: Configuring option h264iframeperiod (00990a66) = 30
May 23 09:09:38 octopi sh[1304]: device/v4l2/device_options.c: VIDEO: Configuring option h264level (00990a67) = 11
May 23 09:09:38 octopi sh[1304]: device/v4l2/device_options.c: VIDEO: Configuring option h264profile (00990a6b) = 4
May 23 09:09:38 octopi sh[1304]: device/v4l2/device_options.c: VIDEO: Configuring option h264minimumqpvalue (00990a61) = 16
May 23 09:09:38 octopi sh[1304]: device/v4l2/device_options.c: VIDEO: Configuring option h264maximumqpvalue (00990a62) = 32
May 23 09:09:38 octopi sh[1304]: device/links.c: ?: Link 0: CAMERA:capture[1920x1080/YUYV/2] => [SNAPSHOT:output:mplane[1920x1056/YUYV/2], RESCALLER:STREAM:>
May 23 09:09:38 octopi sh[1304]: device/links.c: ?: Link 1: SNAPSHOT:capture:mplane[1920x1056/JPEG/2] => [SNAPSHOT-CAPTURE]
May 23 09:09:38 octopi sh[1304]: device/links.c: ?: Link 2: RESCALLER:STREAM:capture:mplane[1312x736/YUYV/2] => [STREAM:output:mplane[1312x736/YUYV/2], VIDE>
May 23 09:09:38 octopi sh[1304]: device/links.c: ?: Link 3: STREAM:capture:mplane[1312x736/JPEG/2] => [STREAM-CAPTURE]
May 23 09:09:38 octopi sh[1304]: device/links.c: ?: Link 4: VIDEO:capture:mplane[1312x736/H264/2] => [VIDEO-CAPTURE]
May 23 09:09:38 octopi sh[1304]: device/buffer_list.c: CAMERA:capture: Streaming started... Was 0 of 2 enqueud
May 23 09:09:38 octopi sh[1304]: device/buffer_list.c: SNAPSHOT:output:mplane: Streaming started... Was 0 of 2 enqueud
May 23 09:09:38 octopi sh[1304]: device/buffer_list.c: RESCALLER:STREAM:output:mplane: Streaming started... Was 0 of 2 enqueud
May 23 09:09:38 octopi sh[1304]: device/buffer_list.c: SNAPSHOT:capture:mplane: Streaming started... Was 0 of 2 enqueud
May 23 09:09:38 octopi sh[1304]: device/buffer_list.c: RESCALLER:STREAM:capture:mplane: Streaming started... Was 0 of 2 enqueud
May 23 09:09:38 octopi sh[1304]: device/buffer_list.c: STREAM:output:mplane: Streaming started... Was 0 of 2 enqueud
May 23 09:09:38 octopi sh[1304]: device/buffer_list.c: VIDEO:output:mplane: Streaming started... Was 0 of 2 enqueud
May 23 09:09:38 octopi sh[1304]: device/buffer_list.c: STREAM:capture:mplane: Streaming started... Was 0 of 2 enqueud
May 23 09:09:38 octopi sh[1304]: device/buffer_list.c: VIDEO:capture:mplane: Streaming started... Was 0 of 2 enqueud
May 23 09:09:55 octopi sh[1304]: util/http/http.c: HTTP8080/0: Client connected 127.0.0.1 (fd=4).
May 23 09:09:55 octopi sh[1304]: util/http/http.c: HTTP8080/0: Request 'GET' '/' 'action=stream'
May 23 09:09:58 octopi sh[1304]: util/http/http.c: HTTP8080/0: Client disconnected 127.0.0.1.

Could there be an (timing) issue with boot/initialization?

from octopi-uptodate.

Could there be an (timing) issue with boot/initialization?

None that I'm aware of, but that "Stale detected" looks like something I've seen in the past as well, with similar symptoms. @ayufan Any ideas what could cause this?

Since the feedback in general looked promising enough regarding stability now, I've gone forward and decided on doing a soft launch.

RPi imager now allows to install the latest build, but the standard one is still there as well and marked as "stable". That should hopefully lead to some more testing yet.

from octopi-uptodate.

New OctoPrint released today, 1.9.0, therefore new image and thus new feedback ticket, see #6

from octopi-uptodate.

@n00b42 @foosel Yes, I see it also on mine. Sometimes it takes slightly longer for bootup, and then subsequent restart is needed. I have my systemd configured to auto restart in 3-5 seconds.

from octopi-uptodate.