Hi All,

I have purchased one of these Spotpear V4 boards to run on a Pi2 B. After contacting the supplier here is the link for a image configured for the display.
http://www.spotpear.com/download/image/RPi-2.4inch_3.2inch-LCD-150602.7z
Or http://www.spotpear.com/download/image/ for alternate displays.
installing this image on a sd card I can confirm all works correctly including the touch screen on my Pi2.
Hope this helps.

from rpi-firmware.

It doesn't say which LCD controller the display uses on that page.

I see the display comes with an image. Isn't that good enough?
If they use FBTFT on that image, see if you find a module starting with fb_ in /sys/module

LCD shields for the Pi is popping up all over the place now. Seven months ago it was only a handful: https://github.com/notro/fbtft/wiki/Raspberry-Pi-Display-shield-comparison

from rpi-firmware.

I have also the old one, but wasnt succesfull getting it to work - to be honest, havnt spent a lot of time.
Is it a ssd1289, at least the driver is named that way, probably I have used wrong kernel parameters for the module.

BTW, this is what the manufacturer supplied:

PIN NO. SYMBOL DESCRIPTION
1, 17 3.3V Power positive (3.3V power input)
2, 4 5V Power positive (5V power input)
11 TP_IRQ Touch screen interrupt, low level while the touch
screen detects touching
12 KEY1 Key
13 KEY2 Key
15 KEY3 Key
19 LCD_SI/TP_SI SPI data input of LCD/touch screen
21 LCD_SO/TP_SO SPI data output of LCD/touch screen
23 LCD_SCK/TP_SCK SPI clock of LCD/touch screen
24 LCD_CS LCD chip selection, low active
26 TP_CS Touch screen chip selection, low active

Any help whould be appreciated.
Thx,
Florian

from rpi-firmware.

Since there is no DC/RS pin I assume it's using the 3-wire SPI mode, which on this controller means 9-bit SPI.
From the top of my head:

sudo modprobe fbtft_device custom name=fb_ssd1289 speed=8000000 buswidth=9 width=XX height=XX

If the width/height of your display differs from 240x320, you have to provide your own init= sequence. The default one assumes this.
Panels differ, so you might have to provide one anyway.

https://github.com/notro/fbtft/wiki/fbtft_device

from rpi-firmware.

Didnt work, but I have done a little more research on these piece of hardware. It is an exact copy of valdodov's circuit and was delivered with the precompiled kernel/modules/configs from his web site.

There was already a ticket in Mai #115 on that matter, is there any chance to get it working ?

Thx,
Florian

from rpi-firmware.

I can't get it to work either. Unfortunately, my display didn't come with an image.

Cheers.

from rpi-firmware.

It is an exact copy of valdodov's circuit ...
is there any chance to get it working ?

No plans to support that circuit.

from rpi-firmware.

I found a custom raspberrian image for this display on a dutch website here:
http://eckstein-shop.de/Plug-and-Play-32-inch-Touch-Screen-TFT-LCD-for-Raspberry-Pi-A-/-B-/-B-_1
NOTE: the archive is password protected (dick move). I've posted on their site to ask for the password.
UPDATE: password for archive is "eckstein", will now see if this is the image we seek.

I also emailed the manufacturer, will post again if either of these leads work.

from rpi-firmware.

Manufacturer refuses to offer any help:

"It seems like the picture is ours.........

If the reseller bought the LCD from us then resell to you, then they must have the CD, as we have CD for each of this LCD screen.
We don't have links for download, all the contents for the LCD are contained in the CD, it should be the resellers problems who did not send the user guide CD to the package.

You can image that if all of the reseller, to whom we have already provided the CD for the products, then they don't send it to customers, then how can we provide the direct services to customers?

Thank you for your understand.
Johanna Liang O(∩_∩)O
Waveshare International Limited
Rm 813, Dynamic World Building, Zhenhua Rd, Futian District, Shenzhen, China
Tel：86-755-83040832
FAX：86-755-83042572
QQ: 2355861372
skype: wvshare
E-mail: [email protected]
Paypal Account: [email protected]
Web：www.wvshare.com"

from rpi-firmware.

Any news on this topic? I am currently also using one of those displays with the image supplied by eckstein. Although this seems to work fine so far, I would prefer to switch to a more open solution (for more recent kernels, etc).

from rpi-firmware.

I copied configuration of the module from that image. It should work but I haven't had the time to try it yet:

https://gist.github.com/balkian/33835d7be3075c023aad

from rpi-firmware.

I also have Waveshare 3.2inch RPi LCD (B) V3 connected to Raspberry Pi Model B+
http://www.wvshare.com/product/3.2inch-RPi-LCD-B.htm
http://www.amazon.com/Waveshare-Raspberry-Resistive-Interface-Rapsberry-pi/dp/B00N0SNVQE

I have found that the initialization string is very close to fb_ili9340 driver, so after few days of testing I found this configuration is pretty stable

1. Use FBTFT drivers built into the kernel

sudo REPO_URI=https://github.com/notro/rpi-firmware BRANCH=builtin rpi-update
sudo reboot

2. After rebooting, check that SPI was created

# dmesg | grep spi
 Linux version 3.12.25+ (pi@raspi2) (gcc version 4.8.3 20140106 (prerelease) (crosstool-NG linaro-1.13.1-4.8-2014.01 - Linaro GCC 2013.11) ) #1 PREEMPT Sat Aug 2 19:08:33 CEST 2014
 bcm2708_spi bcm2708_spi.0: DMA channel 2 at address 0xf2007200 with irq 77
 bcm2708_spi bcm2708_spi.0: DMA channel 4 at address 0xf2007400 with irq 20
 bcm2708_spi bcm2708_spi.0: SPI Controller at 0x20204000 (irq 80)
 bcm2708_spi bcm2708_spi.0: SPI Controller running in dma mode

3. Add to /boot/cmdline.txt (in one line)

fbtft_device.custom
fbtft_device.name=fb_ili9340
fbtft_device.gpios=dc:22,reset:27
fbtft_device.bgr=1
fbtft_device.speed=48000000

4. To enable console on boot add to /boot/cmdline.txt

fbcon=map:10
fbcon=font:ProFont6x11
logo.nologo

5. Also may be useful to add

dma.dmachans=0x7f35
console=tty1
consoleblank=0
fbtft_device.fps=50
fbtft_device.rotate=270

from rpi-firmware.

I've managed to make this work. But has anyone figured out how to make Waveshare 3.2inch RPi LCD work in GUI (startx)? As long as I have a HDMI connected I can see the GUI from an extra screen.

from rpi-firmware.

you want to use them separately or simultaneously?
maybe fbcp will help
https://github.com/notro/fbtft-spindle/wiki/FBTFT-image#fbcp---framebuffer-copy

from rpi-firmware.

I treid fbcp. It copies the big screen (connected through HDMI) which is hanging, into the Waveshare 3.2inch RPi LCD (B) V3. So both screens seems like they hang.

But this is how it's to me.

Normally after making the Waveshare 3.2inch RPi LCD (B) V3-screen work, raspbian runs fine with the little screen. As I only boot into console/terminal. But if I'm going to GUI (startx) the tiny screen hangs.

While booting with an extra screen connected on the HDMI-plug. The extra screen hangs, and the tiny one works fine and mentioned.

When I do the "startx"-command, the HDMI-plugged screen is the one working good in GUI. While the tiny screen hangs.

I wanted to make it so that the tiny screen is standalone and possible to run into GUI (startx). I see the use of fbcp, but it's not for my use.

What I want to do, is to make the tiny screen run fine in GUI (startx). And I'm wondering if you have managed to do that :)

Than you for your time :)

from rpi-firmware.

I have a 3.2inch RPi LCD (B) V3 from waveshare. It came with their DVK512 which includes a CD with an SD image that makes X work on the LCD. Image is Linux raspberrypi 3.12.25+ with (I guess) their custom command: LCD32-SYS-SHOW-V3 which reboots with x on LCD.

from rpi-firmware.

You say the Image is Linux raspberrypi 3.12.25+, so not raspbian customized?

Hmm, do you by any chance have the possibility to upload this anywhere?

from rpi-firmware.

It is too big to upload... It must be available somewhere already. Check this out : http://www.raspberrypi.org/forums/viewtopic.php?f=28&t=89127

from rpi-firmware.

Thank you!
Found this link which have .pdf and the software. So no need for downloading a whole new image into the rasp. pi. Will try this when I have time.

The link: https://docviewer.yandex.com/?url=ya-disk-public%3A%2F%2F3pNBiwUGtdm6B7DR35RIh3ekGYjNeISzNKSlmqcvGds%3D&name=DVD_DVK512_CN_EN_Without_Image.rar&c=547779a0f2ac

from rpi-firmware.

I got my Waveshare 3.2inch LCD working great using the instructions above provided by "imaginal". I now want to be able to turn off the backlight. Has anyone been able to do this? Is the functionality supported?

from rpi-firmware.

Does anyone know how can i turn off the backlight? for the Waveshare 3.2inch LCD

I have been googling everywhere and i cant seem to find it...

from rpi-firmware.

Notro nevermind im going to buy adafruits one and return this chinese one... Thanks :)

from rpi-firmware.

Hiya all.

I have a WaveShare SpotPear V4 LCD with a Raspbian image (unfortunately with loads of excess baggage included, the image is just over 4GB).

I should be able to get it onto the web shortly (give me a few days), I also plan on stripping it back to a very minimal Raspbian with OpenBox and a few utils such as SSH if anybody is interested?

Jim

from rpi-firmware.

Touch working fine (/etc/modules)

snd-bcm2835
i2c-bcm2708
i2c-dev
ads7846_device cs=1 speed=1000000 model=7846 x_min=200 x_max=3840 y_min=200 y_max=3760 x_plate_ohms=60 pressure_max=255 gpio_pendown=17 keep_vref_on=1 swap_xy=0

from rpi-firmware.

@lunarcms
I am very interested, I received my waveshare today and need to use it for first test of my pi b+, I do not have an hdmi monitor.

3.5in rpi LCD (A). Current name of image on the disk: LCD35-14120
So from the instructions on the disc. I believe it is rasbian with display drivers. Now how bad is the bloatware?

I need to format the sd-noob card ( only 4gig card I have) Is it worth losing the noob software and images?

from rpi-firmware.

Could someone look into why drivers built into the kernel is the only way that seems to work?

from rpi-firmware.

would love to make Kodi 14.1 work with this display have tried different configs but all give me some kind of error ie-can't find file, can't find dir, debends on xbmc-deb, no make etc, any help would be great.

Mike

from rpi-firmware.

Okay, I've fiddled around with this stuff. In /etc/modules I have: fbtft_device custom name=fb_ili9340 speed=48000000 gpios=dc:22,reset:27 bgr=1 rotate=270

I added to /boot/cmdline.txt: fbcon=map:10 fbcon=font:ProFont6x11 logo.nologo

The console on startup works just fine, but for some reason, I can't find out how to launch framebuffer applications on the tft display.

I tried su -l pi -c "env FRAMEBUFFER=/dev/fb1 startx &", but that resulted in the tft display being cleared and X starting on the HDMI display.

Any ideas?

edit: ls /dev/ returns:

autofs           input         mem                 ram11   raw        tty12  tty25  tty38  tty50  tty63      vcs3
block            kmsg          mmcblk0             ram12   root       tty13  tty26  tty39  tty51  tty7       vcs4
btrfs-control    log           mmcblk0p1           ram13   shm        tty14  tty27  tty4   tty52  tty8       vcs5
bus              loop0         mmcblk0p2           ram14   snd        tty15  tty28  tty40  tty53  tty9       vcs6
cachefiles       loop1         net                 ram15   sndstat    tty16  tty29  tty41  tty54  ttyAMA0    vcsa
char             loop2         network_latency     ram2    spidev0.1  tty17  tty3   tty42  tty55  ttyprintk  vcsa1
console          loop3         network_throughput  ram3    stderr     tty18  tty30  tty43  tty56  uinput     vcsa2
cpu_dma_latency  loop4         null                ram4    stdin      tty19  tty31  tty44  tty57  urandom    vcsa3
disk             loop5         ppp                 ram5    stdout     tty2   tty32  tty45  tty58  vc-cma     vcsa4
*fb0*              loop6         ptmx                ram6    tty        tty20  tty33  tty46  tty59  vchiq      vcsa5
*fb1*              loop7         pts                 ram7    tty0       tty21  tty34  tty47  tty6   vc-mem     vcsa6
fd               loop-control  ram0                ram8    tty1       tty22  tty35  tty48  tty60  vcs        vcsm
full             MAKEDEV       ram1                ram9    tty10      tty23  tty36  tty49  tty61  vcs1       xconsole
fuse             mapper        ram10               random  tty11      tty24  tty37  tty5   tty62  vcs2       zero

edit: dmesg | grep -i fb returns:

[    0.000000] CPU: ARMv6-compatible processor [410fb767] revision 7 (ARMv7), cr=00c5387d
[    0.000000] Kernel command line: dma.dmachans=0x7f35 bcm2708_fb.fbwidth=1824 bcm2708_fb.fbheight=984 bcm2708.boardrev=0x10 bcm2708.serial=0x4be84e02 smsc95xx.macaddr=B8:27:EB:E8:4E:02 bcm2708_fb.fbswap=1 bcm2708.disk_led_gpio=47 bcm2708.disk_led_active_low=0 sdhci-bcm2708.emmc_clock_freq=250000000 vc_mem.mem_base=0x1ec00000 vc_mem.mem_size=0x20000000  dwc_otg.lpm_enable=0 console=ttyAMA0,115200 console=tty1 root=/dev/mmcblk0p2 rootfstype=ext4 elevator=deadline rootwait fbcon=map:10 fbcon=font:ProFont6x11 logo.nologo
[    1.055686] bcm2708_gpio: bcm2708_gpio_probe c0633fb0
[    1.315312] BCM2708FB: allocated DMA memory 5bc00000
[    1.320487] BCM2708FB: allocated DMA channel 0 @ f2007000
[   12.586432] fbtft_device:  SPI devices registered:
[   12.606322] fbtft_device:      spidev spi0.0 500kHz 8 bits mode=0x00
[   12.621263] fbtft_device:      spidev spi0.1 500kHz 8 bits mode=0x00
[   12.640740] fbtft_device:  'fb' Platform devices registered:
[   12.658823] fbtft_device:      bcm2708_fb id=-1 pdata? no
[   12.671956] fbtft_device: Deleting spi0.0
[   12.686753] fbtft_device:  GPIOS used by 'fb_ili9340':
[   12.717899] fbtft_device:    'dc' = GPIO22
[   12.732129] fbtft_device:    'reset' = GPIO27
[   12.747740] fbtft_device:  SPI devices registered:
[   12.777630] fbtft_device:      spidev spi0.1 500kHz 8 bits mode=0x00
[   12.807621] fbtft_device:      fb_ili9340 spi0.0 48000kHz 8 bits mode=0x00
[   13.444948] graphics fb1: fb_ili9340 frame buffer, 320x240, 150 KiB video memory, 4 KiB DMA buffer memory, fps=20, spi0.0 at 48 MHz

from rpi-firmware.

If Raspian, you need to change fbdev option in /usr/share/X11/xorg.conf.d/99-fbturbo.conf

from rpi-firmware.

thanks @notro :)

from rpi-firmware.

"I should be able to get it onto the web shortly (give me a few days), I also plan on stripping it back to a very minimal Raspbian with OpenBox and a few utils such as SSH if anybody is interested?"

@lunarcms, that would be wonderful. I had a pretty rough time with setting up a 4" Waveshare display because I only had a 4 GB Micro SD and the manufacturer probably had expended all the available space. Have you set something like that up? I couldn't find drivers or a kernel to make the screen work.
Doesn't feel right to have an outdated Raspbian (well, the GUI) with a load of junk installed.

EDIT: Wait, by "V4" did you mean 4 inch or is that unrelated, haha?

from rpi-firmware.

That would be super. I would like to use this for a touch screen tool, so a simple distro would help!

N

Sent from my iPhone

On Jan 15, 2015, at 9:02 AM, bernardlv [email protected] wrote:

"I should be able to get it onto the web shortly (give me a few days), I also plan on stripping it back to a very minimal Raspbian with OpenBox and a few utils such as SSH if anybody is interested?"

lunarcms, that would be wonderful. I had a pretty rough time with setting up a 4" Waveshare display because I only had a 4 GB Micro SD and the manufacturer probably had expended all the available space. Have you set something like that up? I couldn't find drivers or a kernel to make the screen work.

—
Reply to this email directly or view it on GitHub.

from rpi-firmware.

ordered this: got the waveshare 3.2 inch
http://www.amazon.com/gp/product/B00LGOS00G/ref=oh_aui_detailpage_o06_s01?ie=UTF8&psc=1
amazon hosts image here
https://s3.amazonaws.com/lcd32/LCD32-CN.rar

PLUR

from rpi-firmware.

I recently bought the lcd from this site "https://www.crazypi.com/raspberry-pi-products/Raspberry-Pi-Accessories/32-TOUCH-DISPLAY-RASPBERRY-PI".I got a DVD which contain the image file.I am using a B+ board.I burned the image to sd card.But when i power on the board by plugging the display,LCD is completly blank,no backlight ?Please help.I connected a keyboard with raspberry pi through USB port.When i pressed caps lock in keyboard the caps lock light glowed in keyboard.So i think Pi is booting correctly.But LCD is blank.How to check wheather the problem is with SD card,Pi or LCD ?????

from rpi-firmware.

Please contact the seller. They know their display and image.

from rpi-firmware.

Maybe the images for the Odroid which supports the LCD can help?

http://www.hardkernel.com/main/products/prdt_info.php?g_code=G142060963922

from rpi-firmware.

Any one has success with Waveshare 3.2inch V4 on Raspberry Pi 2 Model B?
I tried with image on CD came with it, but no success. It just show Multi Colored Big Block on the screen that cover 90% of screen. And there no response from raspi at all.

Also Tried with Fresh new image of Raspbian 2015-2-16 and running:
sudo REPO_URI=https://github.com/notro/rpi-firmware BRANCH=builtin rpi-update
sudo reboot

Get exact same Multi Colored block on initial screen, same as I get with Image from CD.

Any help?

from rpi-firmware.

sounds like it is booting in hdmi mode.  try pluging a monitor in the hdmi port and rebooting.

 On Tuesday, March 3, 2015 12:59 PM, Vineet <[email protected]> wrote:

Any one has success with Waveshare 3.2inch V4 on Raspberry Pi 2 Model B?
I tried with image on CD came with it, but no success. It just show Multi Colored Big Block on the screen that cover 90% of screen. And there no response from raspi at all.Also Tried with Fresh new image of Raspbian 2015-2-16 and running:
sudo REPO_URI=https://github.com/notro/rpi-firmware BRANCH=builtin rpi-update
sudo rebootGet exact same Multi Colored block on initial screen, same as I get with Image from CD.Any help?—
Reply to this email directly or view it on GitHub.

from rpi-firmware.

Yes, I did that. It was connected with Hdmi, as it was showing that on
monitor. Noticed this is the very first thing usually show on monitor for
few second befit continue with boot. But not it look like stuck on intial
screen and won't continue.

On Tuesday, March 3, 2015, gadget9503 [email protected] wrote:

sounds like it is booting in hdmi mode. try pluging a monitor in the hdmi
port and rebooting.

On Tuesday, March 3, 2015 12:59 PM, Vineet <[email protected]
javascript:_e(%7B%7D,'cvml','[email protected]');> wrote:

Any one has success with Waveshare 3.2inch V4 on Raspberry Pi 2 Model B?
I tried with image on CD came with it, but no success. It just show Multi
Colored Big Block on the screen that cover 90% of screen. And there no
response from raspi at all.Also Tried with Fresh new image of Raspbian
2015-2-16 and running:
sudo REPO_URI=https://github.com/notro/rpi-firmware BRANCH=builtin
rpi-update
sudo rebootGet exact same Multi Colored block on initial screen, same as I
get with Image from CD.Any help?—
Reply to this email directly or view it on GitHub.

—
Reply to this email directly or view it on GitHub
#6 (comment).

from rpi-firmware.

Same problem here , tried several displays and images.
after reboot the rasp freezes multicolor on main hdmi output white screen on the tft...

anyone ?

setup:
Raspberry pi 2 -
Shareware 3,2inch RPI LCD V4

from rpi-firmware.

Highly appreciate if possible to have script or something to setup on my
own Linux image rather than using image come with LCD.

On Wednesday, March 11, 2015, GeertVanMoer [email protected] wrote:

Same problem here , tried several displays and images.
after reboot the rasp freezes multicolor on main hdmi output white screen
on the tft...

anyone ?

setup:
Raspberry pi 2 -
Shareware 3,2inch RPI LCD V4

—
Reply to this email directly or view it on GitHub
#6 (comment).

from rpi-firmware.

Have found another TT i'm now setting up...

http://www.circuitbasics.com/setup-lcd-touchscreen-raspberry-pi/

----- this works rasp working with touch

from rpi-firmware.

Just check the cable on the back side of LCD display....My display wasn't working....After i correctly plugged in the ribbon cable to the board it worked fine....Hope this will help...

from rpi-firmware.

Anyone got it working with splash screen on boot? I tried to follow instruction from https://github.com/notro/fbtft/wiki/Bootsplash

But seems something missing as it does not work for me. Any help?

from rpi-firmware.

initramfs is done differently with the current Device Tree kernels.
I haven't had time to look into it.
There's something in this thread: http://www.raspberrypi.org/forums/viewtopic.php?p=685709&sid=61c7334eb300ad23c03fb28f94e37d7c#p685709
If you make it work and have the time, please update the fbtft bootsplash wiki page.

from rpi-firmware.

Notro, I'm not very much experience with RPi, new learner here. If you can point me to some source I can definitely try. Above link has some info but not able to make out much sense out of it as I'm not even sure what initramfs does and why it used other than is loaded initially during boot sequence.

Any pointer would be helpful for me to look for solution.

On Side note:
I tried to do BRANH=builtin rpi-update expecting with get kernel with built into it and that might help, but that also got my LCD screen to go back to white blank and when check on hdmi output it stuck with initial Rainbow screen and no progress with boot.

from rpi-firmware.

BRANCH=builtin is deprecated. I haven't got time to make it anymore. As soon as we get a SPI DMA driver in the official kernel release, I will stop releasing the BRANCH=master kernel also.

initramfs is loaded very early in the boot process, and at that point you can load the fbtft drivers and plymouth will also start if enabled.

Divide your work into steps, first find out how to make and load an initramfs, then when it works, start filling it. I use google when I don't know how to do something. Usually I get multiple takes an the problem.

from rpi-firmware.

I bought the v4 version (http://www.aliexpress.com/item/3-2-LCD-Touch-Screen-Display-Monitor-Case-Heatsinks-for-Raspberry-Pi-B/32235705777.html) and managed to get it working on a pi1 model B with raspbian installed.
Does anyone have a GPIO script to control the buttons ? Basically i want to turn the display on/off by pressing a button.
I found this: http://www.circuitbasics.com/raspberry-pi-touchscreen-calibration-screen-rotation/#comment-145
but i cant find any command to turn the screen on/off to use it.

from rpi-firmware.

Hi when doin the 1st step
Touchscreen Setup and Configuration

1. First we need to configure the fbturbo video driver to output the display of the Raspberry Pi to the SPI bus instead of the HDMI bus. At the command prompt, enter: sudo nano /usr/share/X11/xorg.conf.d/99-fbturbo.conf

I get it come up but its empty nothing in it atall

from rpi-firmware.

I followed these steps but on reboot it just hung on the following screen

rebuilding rasbian now all I know about my screen is as it says on back
4INCH RPI LCD(A)
WAVESHARE SPOTPARE

from rpi-firmware.

I kbow the screen works with the supplied image but don't wanna use theres cus i wanna use mine so i can chose to boot rasp or openelec

from rpi-firmware.

heres a script of the info I see from the given image from following the guide steps could it be possible to just copy these into the original official rasb image

step1
file is empty

step 2
GNU nano 2.2.6 File: /etc/modprobe.d/raspi-blacklist.conf

blacklist spi and i2c by default (many users don't need them)

#blacklist spi-bcm2708
#blacklist i2c-bcm2708
blacklist snd-soc-pcm512x
blacklist snd-soc-wm8804

step 3
not done as screen working

ste 4
file is empty

step 5
GNU nano 2.2.6 File: /boot/cmdline.txt

dwc_otg.lpm_enable=0 console=ttyAMA0,115200 console=tty1 root=/dev/mmcblk0p2 ro$
$0p2 rootfstype=ext4 elevator=deadline rootwait fbcon=map:10 fbcon=font:ProFont$
$roFont6x11 logo.nologo

step 6
GNU nano 2.2.6 File: /etc/rc.local

#!/bin/sh -e

rc.local

This script is executed at the end of each multiuser runlevel.

Make sure that the script will "exit 0" on success or any other

value on error.

In order to enable or disable this script just change the execution

bits.

By default this script does nothing.

Print the IP address

_IP=$(hostname -I) || true
if [ "$_IP" ]; then
printf "My IP address is %s\n" "$_IP"
fi
su -l pi -c "env FRAMEBUFFER=/dev/fb1 startx -- -dpi 60 &"
[ Read 20 lines ]
GNU nano 2.2.6 File: /etc/rc.local Modified

fi
su -l pi -c "env FRAMEBUFFER=/dev/fb1 startx -- -dpi 60 &"
exit 0

                           [ Read 20 lines ]

from rpi-firmware.

Hi Guys,
I'm hanging to get my LCD Waveshare Spotpear V4 get working with my Raspberry B (not+ not 2)
Trying anythin i would found on the net.. The best solution i think were from here..
As i could se Drivers will load correctly at Startup until on Point:

[Quote]
[ 14.312643] fbtft: module is from the staging directory, the quality is unknown, you have been warned.
[ 14.358515] flexfb: module is from the staging directory, the quality is unknown, you have been warned.
[ 14.517474] fbtft_device: module is from the staging directory, the quality is unknown, you have been warned.
[ 14.541098] fbtft_device: SPI devices registered:
[ 14.554769] fbtft_device: ads7846 spi0.1 2000kHz 8 bits mode=0x00
[ 14.570001] fbtft_device: 'fb' Platform devices registered:
[ 14.584371] fbtft_device: bcm2708_fb id=-1 pdata? no
[ 14.606112] flexfb spi0.0: fbtft_request_gpios: 'reset' = GPIO25
[ 14.634933] flexfb spi0.0: fbtft_request_gpios: 'dc' = GPIO24
[ 14.651362] flexfb spi0.0: flexfb_verify_gpios_dc()
[ 14.665004] flexfb spi0.0: fbtft_init_display()
[ 14.678304] flexfb spi0.0: fbtft_reset()
[ 14.810723] flexfb spi0.0: init: write(0xB0) 0x00
[ 14.824177] flexfb spi0.0: init: write(0x11)
[ 14.837071] flexfb spi0.0: init: mdelay(250)
[ 15.101778] flexfb spi0.0: init: write(0x3A) 0x55
[ 15.115170] flexfb spi0.0: init: write(0xC2) 0x44
[ 15.128523] flexfb spi0.0: init: write(0xC5) 0x00 0x00 0x00 0x00
[ 15.143091] flexfb spi0.0: init: write(0xE0) 0x0F 0x1F 0x1C 0x0C 0x0F 0x08 0x48 0x98 0x37 0x0A 0x13 0x04 0x11 0x0D 0x00
[ 15.162596] flexfb spi0.0: init: write(0xE1) 0x0F 0x32 0x2E 0x0B 0x0D 0x05 0x47 0x75 0x37 0x06 0x10 0x03 0x24 0x20 0x00
[ 15.182092] flexfb spi0.0: init: write(0xE2) 0x0F 0x32 0x2E 0x0B 0x0D 0x05 0x47 0x75 0x37 0x06 0x10 0x03 0x24 0x20 0x00
[ 15.205671] flexfb spi0.0: init: write(0x36) 0x28
[ 15.235770] flexfb spi0.0: init: write(0x11)
[ 15.250259] flexfb spi0.0: init: write(0x29)
[ 15.436973] flexfb spi0.0: Display update: 1726 kB/s (173.685 ms), fps=0 (0.000 ms)
[ 15.459561] flexfb spi0.0: fbtft_register_backlight()
[ 15.473057] flexfb spi0.0: fbtft_register_backlight(): led pin not set, exiting.
[/Quote]
then this Screen doesn't work anymore
with "dmesg" on the second Screen it Shows adittional:

[Quote]
[ 15.568076] graphics fb1: flexfb frame buffer, 480x320, 300 KiB video memory, 4 KiB DMA buffer memory, fps=20, spi0.0 at 16 MHz
[ 15.583015] fbtft_device: GPIOS used by 'flexfb':
[ 15.589465] fbtft_device: 'reset' = GPIO25
[ 15.595371] fbtft_device: 'dc' = GPIO24
[ 15.600897] fbtft_device: SPI devices registered:
[ 15.607320] fbtft_device: ads7846 spi0.1 2000kHz 8 bits mode=0x00
[ 15.616539] fbtft_device: flexfb spi0.0 16000kHz 8 bits mode=0x00
[ 25.792471] smsc95xx 1-1.1:1.0 eth0: hardware isn't capable of remote wakeup
[ 27.348930] smsc95xx 1-1.1:1.0 eth0: link up, 100Mbps, full-duplex, lpa 0xCDE1
[/Quote]

and no Output to the Display..

sorry for my english...

Any ideas ?

from rpi-firmware.

Hi,
I also have the same issues but just found out the drivers and manual on the Wiki
http://www.waveshare.com/wiki/3.2inch_RPi_LCD_(B)

At work, so I will try to test it on the week-end.

from rpi-firmware.

This is was i found too...
but no luck...
the same as described... hanging at booting at:

[ 15.769071] fbtft_device: SPI devices registered:
[ 15.784742] fbtft_device: spidev spi0.0 500kHz 8 bits mode=0x00
[ 15.801762] fbtft_device: spidev spi0.1 500kHz 8 bits mode=0x00
[ 15.818659] fbtft_device: 'fb' Platform devices registered:
[ 15.834897] fbtft_device: bcm2708_fb id=-1 pdata? no
[ 15.850743] fbtft_device: Deleting spi0.0
[ 15.869037] fbtft_device: GPIOS used by 'flexfb':
[ 15.906714] fbtft_device: 'dc' = GPIO22
[ 15.936008] fbtft_device: 'reset' = GPIO27
[ 15.961411] fbtft_device: SPI devices registered:
[ 15.976767] fbtft_device: spidev spi0.1 500kHz 8 bits mode=0x00
[ 15.993732] fbtft_device: flexfb spi0.0 48000kHz 8 bits mode=0x00
[ 16.442000] graphics fb1: flexfb frame buffer, 320x240, 150 KiB video memory, 4 KiB DMA buffer memory, fps=20, spi0.0 at 48 MHz

using Raspian Image from 05.05.2015..

from rpi-firmware.

I little workout around but it WORK fine on Pi 1 & Pi2!

Since I had a few extra MicroSD card, I install a fresh Raspbian from Feb (3.18.5-v7+ ) on one and install the drivers has suggest in http://www.waveshare.com/wiki/3.2inch_RPi_LCD_(B). It WORK! Speed is great and touch work very good without any calibration. I will have more time to play with it on Sunday and see if we do a upgrade it break the drivers.

from rpi-firmware.

Does new rasbian release in May include fbtft with kernel? Or it still need
to build module and include with kernel manually?

On Friday, May 29, 2015, starwolf73 [email protected] wrote:

I little workout around but it WORK fine on Pi 1 & Pi2!

Since I had a few extra MicroSD card, I install a fresh Raspbian from Feb
(3.18.5-v7+ ) on one and install the drivers has suggest in
http://www.waveshare.com/wiki/3.2inch_RPi_LCD_(B). It WORK! Speed is
great and touch work very good without any calibration. I will have more
time to play with it on Sunday and see if we do a upgrade it break the
drivers.

—
Reply to this email directly or view it on GitHub
#6 (comment).

from rpi-firmware.

I was able to run also the latest Raspbian image (May) and it work well. Just make sure to block the bootloader update before any apt-get upgrade. See the Wiki for more info since I'm away from home for now.

from rpi-firmware.

So new release still need to follow all steps from wiki including
installing driver? As I thought drive is included with kernel and will be
part of kernel modules, is that not correct?

On Sat, May 30, 2015 at 9:34 PM, starwolf73 [email protected]
wrote:

I was able to run also the latest Raspbian image (May) and it work well.
Just make sure to block the bootloader update before any apt-get upgrade.
See the Wiki for more info since I'm away from home for now.

—
Reply to this email directly or view it on GitHub
#6 (comment).

from rpi-firmware.

Well, I'm still new to raspi. I do know that my LCD work fine for now with a fresh image and drivers installation. If I have the time this week, I'll try to go a little deeper and understand what the script is doing and post my research.

from rpi-firmware.

not one of described Solutions worked for me....
so i think either this Display is defective or not compatible with my Raspberry Pi B (no + or 2)

:-(

from rpi-firmware.

@Big111156 Did you try with a fresh Raspbian image (3.18)? And did you install the driver with the command LCD32-show? Also you may want to check to turn on DEVICE-TREE and SPI option in RASPI-CONFIG?

from rpi-firmware.

as my Image is:
Linux raspberrypi 3.18.5+ #1 PREEMPT Fri Feb 6 23:35:59 CET 2015 armv6l

changed to your decided Options, but it hangs...

[ 10.686952] bcm2708_i2c 20205000.i2c: BSC0 Controller at 0x20205000 (irq 79) (baudrate 100000)
[ 13.745997] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null)
[ 14.249378] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null)
[ 15.442994] i2c /dev entries driver
[ 15.608391] fbtft_device: SPI devices registered:
[ 15.646462] fbtft_device: spidev spi0.0 500kHz 8 bits mode=0x00
[ 15.664860] fbtft_device: spidev spi0.1 500kHz 8 bits mode=0x00
[ 15.681841] fbtft_device: 'fb' Platform devices registered:
[ 15.698083] fbtft_device: bcm2708_fb id=-1 pdata? no
[ 15.714000] fbtft_device: Deleting spi0.0
[ 15.732038] fbtft_device: GPIOS used by 'flexfb':
[ 15.766545] fbtft_device: 'dc' = GPIO22
[ 15.787180] fbtft_device: 'reset' = GPIO27
[ 15.802012] fbtft_device: SPI devices registered:
[ 15.817260] fbtft_device: spidev spi0.1 500kHz 8 bits mode=0x00
[ 15.834016] fbtft_device: flexfb spi0.0 48000kHz 8 bits mode=0x00
[ 16.303381] graphics fb1: flexfb frame buffer, 320x240, 150 KiB video memory, 4 KiB DMA buffer memory, fps=20, spi0.0 at 48 MHz
[ 16.431106] ads7846_device: Deleting spi0.1
[ 16.508067] ads7846 spi0.1: touchscreen, irq 411
[ 16.522860] input: ADS7846 Touchscreen as /devices/soc/20204000.spi/spi_master/spi0/spi0.1/input/input2
[ 27.755037] smsc95xx 1-1.1:1.0 eth0: hardware isn't capable of remote wakeup
[ 29.312097] smsc95xx 1-1.1:1.0 eth0: link up, 100Mbps, full-duplex, lpa 0xCDE1
[ 38.001814] Adding 102396k swap on /var/swap. Priority:-1 extents:2 across:2134012k SSFS
[ 60.434326] w1_master_driver w1_bus_master1: Family 0 for 00.800000000000.8c is not registered.
[ 119.795427] w1_master_driver w1_bus_master1: Family 0 for 00.400000000000.46 is not registered.

from rpi-firmware.

Hi everyone, so I've been fighting with my new screen for a few days now and after reading all the posts I could find, and banging my head on the keyboard I finally tried this: http://www.waveshare.com/wiki/3.2inch_RPi_LCD_(B) (posted by starwolf73 above)
I followed the instruction on the site and it just works perfectly.. no calibration, no problems.
Also when I tried to download the package from the above site it was taking a year (20k/s), so I found this as a mirror, and it seems to be much faster: https://ecksteinimg.de/Datasheet/LCD-show.tar.gz

Hope this helps some of you, cheers..

from rpi-firmware.

Hello, just wanted to share the setup I have for running the Waveshare 3.2" V4 display on a Raspberry Pi model B rev. 1 using Arch Linux.

Took me a couple of days to figure it out, but after piecing together information from various posts (many thanks to notro, Hexxeh, Imaginal, the tutorial at http://www.circuitbasics.com/setup-lcd-touchscreen-raspberry-pi, and the Waveshare wiki), I hacked together a working setup.

Step 1) Install rpi-update and firmware

With root permissions:

pacman -S wget
wget https://raw.githubusercontent.com/Hexxeh/rpi-update/master/rpi-update -O /usr/bin/rpi-update
chmod +x /usr/bin/rpi-update

Then I install the builtin branch for notro's rpi-firmware:†

REPO_URI=https://github.com/notro/rpi-firmware BRANCH=builtin rpi-update

Step 2) Configuring modules

I would recommend doing the following by SSHing into the device. You'll be copying large amounts of text and if nothing is displayed on bootup you can recover easily.

With root permissions:

Insert the following line in /boot/config.txt to enable SPI:

dtparam=spi=on

Edit /etc/modules-load.d/raspberrypi.conf and insert the following modules for SPI, display, and touchscreen drivers:†

spi_bcm2708
fbtft_device
ads7846_device

Create the file /etc/modprobe.d/fbtft.conf. Copy the line in, but pay close attention to the gpio pins:‡

options fbtft_device name=waveshare32b width=320 height=240 gpios=dc:22,reset:21 bgr=1 speed=48000000 buswidth=8 rotate=270 init=-1,0xCB,0x39,0x2C,0x00,0x34,0x02,-1,0xCF,0x00,0XC1,0X30,-1,0xE8,0x85,0x00,0x78,-1,0xEA,0x00,0x00,-1,0xED,0x64,0x03,0X12,0X81,-1,0xF7,0x20,-1,0xC0,0x23,-1,0xC1,0x10,-1,0xC5,0x3e,0x28,-1,0xC7,0x86,-1,0x36,0x28,-1,0x3A,0x55,-1,0xB1,0x00,0x18,-1,0xB6,0x08,0x82,0x27,-1,0xF2,0x00,-1,0x26,0x01,-1,0xE0,0x0F,0x31,0x2B,0x0C,0x0E,0x08,0x4E,0xF1,0x37,0x07,0x10,0x03,0x0E,0x09,0x00,-1,0XE1,0x00,0x0E,0x14,0x03,0x11,0x07,0x31,0xC1,0x48,0x08,0x0F,0x0C,0x31,0x36,0x0F,-1,0x11,-2,120,-1,0x29,-1,0x2c,-3

Step 3) Bootup commands

Back up /boot/cmdline.txt to your home folder if you need to restore it later.

cp /boot/cmdline.txt ~/cmdline.txt.bak

Erase everything in /boot/cmdline.txt and copy this line:

root=/dev/mmcblk0p2 rw rootwait selinux=0 plymouth.enable=0 smsc95xx.turbo_mode=N dwc_otg.lpm_enable=0 kgdboc=ttyAMA0,115200 elevator=noop fbtft_device.custom fbtft_device.name=waveshare32b fbtft_device.gpios=dc:22,reset:21 fbtft_device.bgr=1 fbtft_device.speed=48000000 fbtft_device.fps=50 fbtft_device.rotate=270 dma.dmachans=0x7f35 console=ttyAMA0,115200 fbcon=map:10 fbcon=font:VGA8x8 console=tty1 consoleblank=0

(This will boot into the command line on the Waveshare display. If you want the command line on your primary display with HDMI or NTSC, remove "fbcon=map:10 fbcon=font:VGA8x8". Booting fbcon this way is deprecated in future releases.)

Step 4) Reboot

That's it! The display should work and you should see the command line on it now.

† The builtin branch is deprecated, but I got a square display with unused white bars on the side when I set it up with the newer kernel. I haven't figured out a solution yet. Keep in mind that fbtft_device, ads7846_device, and fbcon might not work the same way in newer releases.
‡ The Raspberry Pi Rev. 1 models A and B have a slightly different pinout for GPIO. GPIO21 was changed to GPIO27 in all future revisions, so change the reset pin accordingly.

from rpi-firmware.

I have a WaveShare 3.5 RPI LCD (A) (http://www.wvshare.com/product/3.5inch-RPi-LCD-A.htm) and cannot get it to work following this guide. I have Kali Linux installed with TFT made specifically for the Raspberry Pi (including A). I followed ieidsath guide and first /boot/config.txt and /boot/cmdline.txt did not exist (don't know if that has anything to do with it not working). Besides that I followed the instructions and it still shows the display on the HDMI and none on the LCD screen.

from rpi-firmware.

@ieidsath thx for the info on rev 1! Finally figure out why it didn't work on my board 😃

from rpi-firmware.

@Sergehog101 you are the insanity saver!! Been figuring this for days -

from rpi-firmware.

Could you talk as more about this image??

What is the SO based? Debian? Version kernel?

Did you try to make a dist-upgrade ? Is it working after upgrade ?

Regards
El 28 ene. 2016 11:41, "Sergehog101" [email protected] escribió:

Hi All,

I have purchased one of these Spotpear V4 boards to run on a Pi2 B. After
contacting the supplier here is the link for a image configured for the
display.
http://www.spotpear.com/download/image/RPi-2.4inch_3.2inch-LCD-150602.7z
After installing this image on a sd card I can confirm all works correctly
including the touch screen on my Pi2.
Hope this helps.

—
Reply to this email directly or view it on GitHub
#6 (comment).

from rpi-firmware.

for all of you trying to get the following screen to work on pi B rev1
http://www.waveshare.com/3.2inch-rpi-lcd-b.htm
you need to download the image from the website, install/write to SD card,
then
sudo nano /etc/modules
and change this bit: gpios=dc:22,reset:27
to gpios=dc:22,reset:21
and your screen will work ...and work in startx
i don't think anyone has been paying any attention to the pin-outs of their screens and the pin-outs of the gpio's on their versions of the raspi! if it doesn't match the code... it ain't gonna work!

from rpi-firmware.

Hi notro,
I am using chromium OS in raspberry pi 3 board with waveshare 3.2 inch TFT display. Chromium OS has Linux kernel 4.4, FBTFT drivers are built part of kernel. I followed the overlay procedure with the waveshare dtb, but on boot up, it gets stuck with the following kernel messages. Any solution ??

from rpi-firmware.

Use a HDMI monitor to see if there are more messages. FBTFT won't display panic messages.

from rpi-firmware.

Allright, the only thing y'all need to do is follow the dts/dtb instructions here: https://github.com/swkim01/waveshare-dtoverlays

Basically copy the dtb file to your /boot/overlay/, add dtoverlay=waveshare35a to config.txt, reboot. Done :)

from rpi-firmware.

@fbettag does that include the raspberry 3? I just got this LCD and tried to do what is on waveshare page http://www.waveshare.com/wiki/3.2inch_RPi_LCD_(B) but, I get a kernel panic when It reboots.

from rpi-firmware.

yes should work for rpi1-3. I had it plugged on my 2 and 3, dunno where my 1 is

from rpi-firmware.

just tried it and all I get is a block screen during boot. It shows a bit of the booting process then goes blank.

from rpi-firmware.

well if it shows your cli during boot then it works, you're just suffering some misconfiguration. Xorg and fbcp setup properly?

from rpi-firmware.

where can I find how to configure those? I appreciate the help.

from rpi-firmware.

maybe my blogpost helps http://uberblo.gs/2016/12/kali-on-the-raspberrypi-with-3-5inch-lcd

from rpi-firmware.

dhineshc

Change your pinouts references
Dc = 22
Reset = 25 on pi3 i think
And make sure you've checked the information others have posted on this. Send more screen shots of all the info during boot

from rpi-firmware.

Sorry correction
DC = 22 (GPIO 25)
RESET = 21 (GPIO 9)
Do not use 27 as reset, that is the I²C id for the eeprom

Sudo nano /etc/modules
Change
fbtft_device name=waveshare32b gpios=dc:22,reset:27 speed=48000000

To this
fbtft_device name=waveshare32b gpios=dc:22,reset:21 speed=48000000

The below is how i set mine up, just changed the gpios to match pinouts of the screen & pi
Www.circuitbasics.com/setup-lcd-touchscreen-raspberry-pi/

from rpi-firmware.

Hi,
I try to replace my squeeezeboxplayer using raspeberry pi 3, picore player (tinycore linux) and my waveshare 3.5.
I tried all procedure I known but I still have a white screen (the HDMI is working correctly). do you have a procedure for tiny core ( kernel 4.4.39) that I could use without having X11 installed?
thanks for your help

from rpi-firmware.