Comments (8)
nebkat
commented on June 15, 2024
Hi @n8it,
The first 2 screenshots seem to suggest the flashing was successful, and I was able to flash successfully myself. The third screenshot is showing that the device is still in download mode (awaiting new firmware from the PC). Have you tried unplugging the SRTK2B, pressing the XBee Reset button, etc?
from esp32-xbee.
n8it
commented on June 15, 2024
After the download finishes as shown in the first two screenshots, I open the terminal and there is no output. I then press the reset button on the simpleRTK2B board and then I get the repeating 7 line blocks until I press the boot button on the esp32 board and that produces the last 2 lines as shown. I had no issues loading V0.44 without power cycle which is what I did after my problem with V0.50.
I will try again with a cold start, erase flash, power cycle and follow the wiki line by line.
from esp32-xbee.
n8it
commented on June 15, 2024
I downloaded the 4 V0.50 files again and did a cold start, erase flash, power cycle and followed the wiki line by line I still have the same results as my screenshots. I have loaded V0.44 again for now. I will work on this again over the weekend. Thanks for taking a look at it.
from esp32-xbee.
nebkat
commented on June 15, 2024
@n8it did you have any luck with this? It appears others have been able to flash without any issue, so I'm not sure what exactly is happening in your case. As far as the flashing process is concerned there should be no difference between which exact binaries are being flashed, so its very unusual that v0.4.4 works for you but not v0.5.
from esp32-xbee.
AndrewR-L
commented on June 15, 2024
Just to say I upgraded from 0.44 to 0.5 without any problem.
No idea if it is relevant, but I did have SPI MODE set to "DIO" not "QIO" as above (as in the instructions).
from esp32-xbee.
nebkat
commented on June 15, 2024
If this problem continues with v0.5.1 feel free to comment again but I'll close this for now. There seem to be some isolated cases of this but I don't think its actually related to the firmware.
from esp32-xbee.
n8it
commented on June 15, 2024
I loaded V0.5.1 on my three simpleRTX2B esp32-xbee devices without any issues. All three would error out with v0.5.
When I connected all three of my devices to my NTRIP service, it shows all three Rovers as a "ESP32_XBee_Ntrip_Client" with Rover Firmware "1.0" .It would be very helpfull if these names could be configured in the esp32 xbee config.
On Monday, February 10, 2020, 3:53:45 PM EST, Nebojša Cvetković <[email protected]> wrote:
If this problem continues with v0.5.1 feel free to comment again but I'll close this for now. There seem to be some isolated cases of this but I don't think its actually related to the firmware.
—
You are receiving this because you were mentioned.
Reply to this email directly, view it on GitHub, or unsubscribe.
from esp32-xbee.
nebkat
commented on June 15, 2024
Very unusual but I'm glad it appears to have resolved itself.
I'll consider adding an option for that, thanks for the suggestion!
from esp32-xbee.
Related Issues (20)
- send nmea data from socket server over http
- NTRIP Caster not working HOT 1
- Configuration Issue.
- Issues with Android 11 HOT 1
- ESP-IDF Version to Build 0.5.4? HOT 1
- Add bluetooth support for obtaining NMEA HOT 12
- DJI Controller unable to connect
- Hotspot not working on v0.5.3 and v0.5.4
- Add VSCode / PlatformIO project & build instructions as alternative to uploading pre-built binaries HOT 1
- Question: Can you explain IP forwarding/NATP ? HOT 1
- RTK2go.com now requires a user email to connect
- ArduSimple WiFi NTRIP Master - cannot set password to hotspot
- Cannot see ESP32 Xbee on Wifi HOT 1
- Firmware installation on classic esp32
- Comparability with browsers.
- WiFi Hotspot lists incorrect Min/Max IP address
- Loss of RTK Base Access after client disconnection
- transferring data between 2 esp32 using XBEE S2c
- Panic reset triggered by switch to UDP as Socket protocol
- Need help with understanding why my ESP32 is disconnecting from caster HOT 7
Recommend Projects
-
React
A declarative, efficient, and flexible JavaScript library for building user interfaces.
-
Vue.js
🖖 Vue.js is a progressive, incrementally-adoptable JavaScript framework for building UI on the web.
-
Typescript
TypeScript is a superset of JavaScript that compiles to clean JavaScript output.
-
TensorFlow
An Open Source Machine Learning Framework for Everyone
-
Django
The Web framework for perfectionists with deadlines.
-
Laravel
A PHP framework for web artisans
-
D3
Bring data to life with SVG, Canvas and HTML. 📊📈🎉
-
Recommend Topics
-
javascript
JavaScript (JS) is a lightweight interpreted programming language with first-class functions.
-
web
Some thing interesting about web. New door for the world.
-
server
A server is a program made to process requests and deliver data to clients.
-
Machine learning
Machine learning is a way of modeling and interpreting data that allows a piece of software to respond intelligently.
-
Visualization
Some thing interesting about visualization, use data art
-
Game
Some thing interesting about game, make everyone happy.
Recommend Org
-
Facebook
We are working to build community through open source technology. NB: members must have two-factor auth.
-
Microsoft
Open source projects and samples from Microsoft.
-
Google
Google ❤️ Open Source for everyone.
-
Alibaba
Alibaba Open Source for everyone
-
D3
Data-Driven Documents codes.
-
Tencent
China tencent open source team.
from esp32-xbee.