Comments (13)
kriswiner
commented on September 27, 2024
No idea, I use the L082 system layer/Arduino core to program these.
…On Thu, Mar 5, 2020 at 5:22 PM klyaruqui ***@***.***> wrote:
Hello kris.
I wanna know if I can update the firmware of the LoRaSensorTile.v05 to
program in python or another language. Because arduino ide consume more
resources
—
You are receiving this because you are subscribed to this thread.
Reply to this email directly, view it on GitHub
<#23?email_source=notifications&email_token=ABTDLKWCGJJY4ZFLH5W7IILRGBF5NA5CNFSM4LCWN2NKYY3PNVWWK3TUL52HS4DFUVEXG43VMWVGG33NNVSW45C7NFSM4IS6YPJQ>,
or unsubscribe
<https://github.com/notifications/unsubscribe-auth/ABTDLKW77LP5NRNBLNU3ZYTRGBF5NANCNFSM4LCWN2NA>
.
from cmwx1zzabz.
klyaruqui
commented on September 27, 2024
thanks Kris
I'll ask another question in the future :)
from cmwx1zzabz.
kriswiner
commented on September 27, 2024
Not sure what your concern is with the Arduino core for the L082. It is
power and memory efficient, robust, and complete. What resources do you
think are being consumed?
…On Thu, Mar 5, 2020 at 5:32 PM klyaruqui ***@***.***> wrote:
thanks Kris
I'll ask to another question in the future :)
—
You are receiving this because you commented.
Reply to this email directly, view it on GitHub
<#23?email_source=notifications&email_token=ABTDLKX7CGLZSX7CGR5OIKLRGBHEBA5CNFSM4LCWN2NKYY3PNVWWK3TUL52HS4DFVREXG43VMVBW63LNMVXHJKTDN5WW2ZLOORPWSZGOEN7WN3A#issuecomment-595551980>,
or unsubscribe
<https://github.com/notifications/unsubscribe-auth/ABTDLKWFSBMYLKC2QQO3E7DRGBHEBANCNFSM4LCWN2NA>
.
from cmwx1zzabz.
klyaruqui
commented on September 27, 2024
Thanks Kris I will do with the Arduino core
from cmwx1zzabz.
K0I05
commented on September 27, 2024
Hello Kris,
I installed board support for the sensor tile per instructions and downloaded the entire library (i.e. CMWX1ZZABZ) via github. I updated the v05 sketch (LoRa settings to match TTN settings), referenced the SPIFlash library appropriately (i.e. SPIFlashClass), and the sketch compiles. However, when I attempt to upload the sketch to the board it fails. The programmer in the sketch defaulted to "AVRISP mkII" but is this correct?
BTW: Arduino IDE 1.8.10 and outputs are appearing via Serial Monitor
Thanks
Eric
from cmwx1zzabz.
kriswiner
commented on September 27, 2024
The programmer is not used so irrelevant.
Did you select Cicada as the board variant?
What is the output on programming failure?
…On Fri, Apr 3, 2020 at 10:58 AM egionet ***@***.***> wrote:
Hello Kris,
I installed board support for the sensor tile per instructions and
downloaded the entire library (i.e. CMWX1ZZABZ) via github. I updated the
v05 sketch (LoRa settings to match TTN settings), referenced the SPIFlash
library appropriately (i.e. SPIFlashClass), and the sketch compiles.
However, when I attempt to upload the sketch to the board it fails. The
programmer in the sketch defaulted to "AVRISP mkII" but is this correct?
BTW: Arduino IDE 1.8.10 and outputs are appearing via Serial Monitor
Thanks
Eric
—
You are receiving this because you commented.
Reply to this email directly, view it on GitHub
<#23 (comment)>,
or unsubscribe
<https://github.com/notifications/unsubscribe-auth/ABTDLKTAHO64ECGULWL7S6DRKYPVHANCNFSM4LCWN2NA>
.
from cmwx1zzabz.
K0I05
commented on September 27, 2024
Arduino: 1.8.10 (Linux), Board: "Cicada-L082CZ, Serial, None, 32 MHz, Smallest Code"
Sketch uses 100672 bytes (51%) of program storage space. Maximum is 196608 bytes.
Global variables use 7264 bytes (35%) of dynamic memory, leaving 13216 bytes for local variables. Maximum is 20480 bytes.
10
9
8
7
6
5
4
3
2
1
FAIL
Board at /dev/ttyACM0 is not available
This report would have more information with
"Show verbose output during compilation"
option enabled in File -> Preferences.
from cmwx1zzabz.
kriswiner
commented on September 27, 2024
Close Arduino IDE.
Press and hold boot button, press and release reset button, replease boot
button
Open ARduino IDE, select Cicada board variant, there should be no COM port
showing in the tools menu
Flash a blink program, the pc should assign a COM port.
This procedure is required upon flashing errors (like when you use the
wrong board variant) but otherwise flashing should occur as normal with the
Arduino IDE.
If the board still does not flash (or you still get the 1 - 10 countdown,
there is a driver issue, Download and run Zadig, list all devices, select
STM32 bootloader, and click replace driver and try to flash again.
…On Fri, Apr 3, 2020 at 11:20 AM egionet ***@***.***> wrote:
Arduino: 1.8.10 (Linux), Board: "Cicada-L082CZ, Serial, None, 32 MHz,
Smallest Code"
Sketch uses 100672 bytes (51%) of program storage space. Maximum is 196608
bytes.
Global variables use 7264 bytes (35%) of dynamic memory, leaving 13216
bytes for local variables. Maximum is 20480 bytes.
10
9
8
7
6
5
4
3
2
1
FAIL
Board at /dev/ttyACM0 is not available
This report would have more information with
"Show verbose output during compilation"
option enabled in File -> Preferences.
—
You are receiving this because you commented.
Reply to this email directly, view it on GitHub
<#23 (comment)>,
or unsubscribe
<https://github.com/notifications/unsubscribe-auth/ABTDLKQFVA623GO63NPOUQ3RKYSGZANCNFSM4LCWN2NA>
.
from cmwx1zzabz.
K0I05
commented on September 27, 2024
countdown still occurs. i'm on ubuntu and not windows
from cmwx1zzabz.
kriswiner
commented on September 27, 2024
So you are using the Arduino IDE on ubuntu linux?
Special case, maybe Thomas can help....
…On Fri, Apr 3, 2020 at 11:43 AM egionet ***@***.***> wrote:
countdown still occurs. i'm on ubuntu and not windows
—
You are receiving this because you commented.
Reply to this email directly, view it on GitHub
<#23 (comment)>,
or unsubscribe
<https://github.com/notifications/unsubscribe-auth/ABTDLKUEYDOY4XL5KAPNRU3RKYU3ZANCNFSM4LCWN2NA>
.
from cmwx1zzabz.
K0I05
commented on September 27, 2024
correct, I will give it a try on a windows machine...
from cmwx1zzabz.
GrumpyOldPizza
commented on September 27, 2024
Do you have the 32 bit library support (like libc and such) installed on Ubuntu ?
from cmwx1zzabz.
K0I05
commented on September 27, 2024
I will check. The board works fine on Windows after updating via Zadig and finally seeing data on TTN through the Dragino LPS8.
from cmwx1zzabz.
Related Issues (20)
- GNSS always busy--can't progress HOT 14
- LongCricket BME280 odd data HOT 31
- How Can I receive LoRa Data? HOT 5
- Hang on LoRaWAN.joinOTAA(appEui, appKey, devEui); HOT 5
- xxMhz timer not working. HOT 1
- Question: Is it possible to change the callback delay? HOT 2
- LORAWAN_DEFAULT_PORT override HOT 3
- CAD detected HOT 2
- Ping Pong Example Not Available HOT 1
- Downlink Data Location and Receive Window Time HOT 6
- BME280 using spi HOT 1
- issue with PB7 HOT 2
- B-L072Z-LRWAN1 Arduino Sketch Uploading Error HOT 8
- how to reset the uplink counter HOT 2
- AT COMANDS HOT 1
- lorawan mac version HOT 4
- Documentation of lora and activity timing HOT 1
- GasCapPowerUsage
- SquirrelTrackingApplication
Recommend Projects
-
React
A declarative, efficient, and flexible JavaScript library for building user interfaces.
-
Vue.js
🖖 Vue.js is a progressive, incrementally-adoptable JavaScript framework for building UI on the web.
-
Typescript
TypeScript is a superset of JavaScript that compiles to clean JavaScript output.
-
TensorFlow
An Open Source Machine Learning Framework for Everyone
-
Django
The Web framework for perfectionists with deadlines.
-
Laravel
A PHP framework for web artisans
-
D3
Bring data to life with SVG, Canvas and HTML. 📊📈🎉
-
Recommend Topics
-
javascript
JavaScript (JS) is a lightweight interpreted programming language with first-class functions.
-
web
Some thing interesting about web. New door for the world.
-
server
A server is a program made to process requests and deliver data to clients.
-
Machine learning
Machine learning is a way of modeling and interpreting data that allows a piece of software to respond intelligently.
-
Visualization
Some thing interesting about visualization, use data art
-
Game
Some thing interesting about game, make everyone happy.
Recommend Org
-
Facebook
We are working to build community through open source technology. NB: members must have two-factor auth.
-
Microsoft
Open source projects and samples from Microsoft.
-
Google
Google ❤️ Open Source for everyone.
-
Alibaba
Alibaba Open Source for everyone
-
D3
Data-Driven Documents codes.
-
Tencent
China tencent open source team.
from cmwx1zzabz.