Comments (12)
We need to see your existing config file to be able to help.
Please cut and paste on a reply.
from fluidnc.
from fluidnc.
This is the boardThat I am trying to use.
from fluidnc.
I have no knowledge of that controller. It is not on our known hardware list.
Can you provide links to the schematic, datasheet and where you got it. Have you contacted the supplier for help?
I am pasting your file here. It has a lot of NO_PIN values, that we cannot help you with.
board: 6 Pack
name:Laser Home XYZ
meta: 2024 Gary
stepping:
engine: I2S_stream
idle_ms: 255
pulse_us: 4
dir_delay_us: 1
disable_delay_us: 0
segments: 12
axes:
shared_stepper_disable_pin: NO_PIN
x:
steps_per_mm: 533.366616
max_rate_mm_per_min: 4000.000
acceleration_mm_per_sec2: 80.000
max_travel_mm: 900.000
soft_limits: true
homing:
cycle: 2
allow_single_axis: true
positive_direction: false
mpos_mm: 0.000
feed_mm_per_min: 300.000
seek_mm_per_min: 600.000
settle_ms: 500
seek_scaler: 1.100
feed_scaler: 1.100
motor0:
limit_neg_pin: NO_PIN
limit_pos_pin: NO_PIN
limit_all_pin: NO_PIN
hard_limits: true
pulloff_mm: 3.000
stepstick:
step_pin: I2SO.2
direction_pin: I2SO.1
disable_pin: I2SO.0
ms1_pin: NO_PIN
ms2_pin: NO_PIN
ms3_pin: I2SO.3
reset_pin: NO_PIN
y:
steps_per_mm: 533.366616
max_rate_mm_per_min: 4000.000
acceleration_mm_per_sec2: 80.000
max_travel_mm: 1300.000
soft_limits: true
homing:
cycle: 2
allow_single_axis: true
positive_direction: true
mpos_mm: 0.000
feed_mm_per_min: 300.000
seek_mm_per_min: 600.000
settle_ms: 500
seek_scaler: 1.100
feed_scaler: 1.100
motor0:
limit_neg_pin: NO_PIN
limit_pos_pin: NO_PIN
limit_all_pin: NO_PIN
hard_limits: true
pulloff_mm: 1.000
stepstick:
step_pin: I2SO.5
direction_pin: I2SO.4
disable_pin: I2SO.7
ms1_pin: NO_PIN
ms2_pin: NO_PIN
ms3_pin: I2SO.6
reset_pin: NO_PIN
z:
steps_per_mm: 533.366616
max_rate_mm_per_min: 4000.000
acceleration_mm_per_sec2: 50.000
max_travel_mm: 20.000
soft_limits: true
homing:
cycle: 1
allow_single_axis: true
positive_direction: true
mpos_mm: 0.000
feed_mm_per_min: 300.000
seek_mm_per_min: 600.000
settle_ms: 500
seek_scaler: 1.100
feed_scaler: 1.100
motor0:
limit_neg_pin: NO_PIN
limit_pos_pin: NO_PIN
limit_all_pin: NO_PIN
hard_limits: false
pulloff_mm: 5.000
standard_stepper:
step_pin: I2SO.10
direction_pin: I2SO.9
disable_pin: I2SO.8
i2so:
bck_pin: gpio.22
data_pin: gpio.21
ws_pin: gpio.17
spi:
miso_pin: gpio.19
mosi_pin: gpio.23
sck_pin: gpio.18
sdcard:
cs_pin: gpio.5
card_detect_pin: NO_PIN
start:
must_home: false
arc_tolerance_mm: 0.002
junction_deviation_mm: 0.010
verbose_errors: false
report_inches: false
enable_parking_override_control: false
use_line_numbers: false
planner_blocks: 16
NoSpindle:
from fluidnc.
It might be this.
https://github.com/Macrobase-tech/CNC-Software/tree/main/6%20Axis%20Upgrade
It does not appear that they reply to issues. I did not see any source files. I did not open any of the .rar files. There is a config file here.
https://github.com/Macrobase-tech/CNC-Software/tree/main/6%20Axis%20Upgrade/Software%20instruction
I do not think it is worth our time to offer free support to this controller.
from fluidnc.
Board.pdf
Sorry it was night time down here when you guys replied. I have an old trimph C02 1300x900 laser which i am trying to convert to diode.
Had it running on a mach3 board but didnt engrave well, so just thought i would try Fluidnc download . Any help with a config
yaml file would be great as it is all very confusing. Thanks all.
from fluidnc.
We spent a lot of time documenting and explaining the config file on the wiki, and provided numerous examples for different situations. Now you are asking us to spend even more time spoon-feeding the information to you, on behalf of barely-documented third-party hardware that hardly anyone else uses. If we created custom config files, for free, for every new user, development would come to a halt and it would not be long before the project died.
from fluidnc.
I was only asking for help as it is so confusing on your website.
from fluidnc.
Here is the diagram from AliExpress.
Have a nice day.
Macrobase_6Axes_Schematic.pdf
from fluidnc.
Thanks for all your help, looks like I should back of this as it seems to complicated. Cheers.
from fluidnc.
That is probably best. Converting a laser can be complicated and dangerous on a lot of levels.
I have added the board to our hardware page for future reference.
from fluidnc.
@Hooks321
try this
Macrobase 6 Axis.zip
board: Macrobase 6 Axis
name: 6 Axis
meta: (29.07.2024) by Skorpi
kinematics:
Cartesian:
stepping:
engine: I2S_STATIC
idle_ms: 255
pulse_us: 4
dir_delay_us: 1
disable_delay_us: 0
axes:
x:
steps_per_mm: 533.366616
max_rate_mm_per_min: 8000.000
acceleration_mm_per_sec2: 300.000
max_travel_mm: 1300.000
soft_limits: true
homing:
cycle: 2
positive_direction: false
mpos_mm: 0.000
feed_mm_per_min: 300.000
seek_mm_per_min: 1500.000
settle_ms: 500
seek_scaler: 1.100
feed_scaler: 1.100
motor0:
limit_neg_pin: gpio.33:low
hard_limits: false
pulloff_mm: 4.000
stepstick:
ms3_pin: i2so.3
step_pin: I2SO.2
direction_pin: I2SO.1
disable_pin: I2SO.0
y:
steps_per_mm: 533.366616
max_rate_mm_per_min: 8000.000
acceleration_mm_per_sec2: 300.000
max_travel_mm: 900.000
soft_limits: true
homing:
cycle: 3
positive_direction: false
mpos_mm: 0.000
feed_mm_per_min: 300.000
seek_mm_per_min: 2000.000
settle_ms: 500
seek_scaler: 1.100
feed_scaler: 1.100
motor0:
limit_neg_pin: gpio.32:low
hard_limits: false
pulloff_mm: 4.000
stepstick:
ms3_pin: i2so.6
step_pin: I2SO.5
direction_pin: I2SO.4
disable_pin: I2SO.7
z:
steps_per_mm: 533.366616
max_rate_mm_per_min: 8000.000
acceleration_mm_per_sec2: 300.000
max_travel_mm: 20.000
soft_limits: true
homing:
cycle: 1
positive_direction: true
mpos_mm: 0.000
feed_mm_per_min: 300.000
seek_mm_per_min: 500.000
settle_ms: 500
seek_scaler: 1.100
feed_scaler: 1.100
motor0:
limit_neg_pin: gpio.35:low
hard_limits: false
pulloff_mm: 3.000
stepstick:
ms3_pin: i2so.11
step_pin: I2SO.10
direction_pin: I2SO.9
disable_pin: I2SO.8
# a:
# steps_per_mm: 800.000
# max_rate_mm_per_min: 8000.000
# acceleration_mm_per_sec2: 300.000
# max_travel_mm: 2500.000
# soft_limits: true
# homing:
# cycle: 2
# positive_direction: false
# mpos_mm: 0.000
# feed_mm_per_min: 300.000
# seek_mm_per_min: 1500.000
# settle_ms: 500
# seek_scaler: 1.100
# feed_scaler: 1.100
#
# motor0:
# limit_neg_pin: NO_PIN
# hard_limits: false
# pulloff_mm: 4.000
# stepstick:
# ms3_pin: i2so.14
# step_pin: I2SO.13
# direction_pin: I2SO.12
# disable_pin: I2SO.15
#
# b:
# steps_per_mm: 800.000
# max_rate_mm_per_min: 8000.000
# acceleration_mm_per_sec2: 300.000
# max_travel_mm: 2500.000
# soft_limits: true
# homing:
# cycle: 2
# positive_direction: false
# mpos_mm: 0.000
# feed_mm_per_min: 300.000
# seek_mm_per_min: 1500.000
# settle_ms: 500
# seek_scaler: 1.100
# feed_scaler: 1.100
#
# motor0:
# limit_neg_pin: NO_PIN
# hard_limits: false
# pulloff_mm: 4.000
# stepstick:
# ms3_pin: i2so.19
# step_pin: I2SO.18
# direction_pin: I2SO.17
# disable_pin: I2SO.16
#
# c:
# steps_per_mm: 800.000
# max_rate_mm_per_min: 8000.000
# acceleration_mm_per_sec2: 300.000
# max_travel_mm: 1250.000
# soft_limits: true
# homing:
# cycle: 3
# positive_direction: false
# mpos_mm: 0.000
# feed_mm_per_min: 300.000
# seek_mm_per_min: 2000.000
# settle_ms: 500
# seek_scaler: 1.100
# feed_scaler: 1.100
#
# motor0:
# limit_neg_pin: NO_PIN
# hard_limits: false
# pulloff_mm: 4.000
# stepstick:
# ms3_pin: i2so.22
# step_pin: I2SO.21
# direction_pin: I2SO.20
# disable_pin: I2SO.23
i2so:
bck_pin: gpio.22
data_pin: gpio.21
ws_pin: gpio.17
spi:
miso_pin: gpio.19
mosi_pin: gpio.23
sck_pin: gpio.18
probe:
pin: gpio.34
check_mode_start: false
sdcard:
cs_pin: gpio.5
coolant:
flood_pin: i2so.24
mist_pin: gpio.4
delay_ms: 0
control:
safety_door_pin: NO_PIN
reset_pin: NO_PIN
feed_hold_pin: gpio.36
cycle_start_pin: NO_PIN
Laser:
pwm_hz: 5000
output_pin: gpio.27
enable_pin: gpio.12
disable_with_s0: false
s0_with_disable: false
tool_num: 0
speed_map: 0=0.000% 1000=100.000%
start:
must_home: false
deactivate_parking: false
check_limits: false
from fluidnc.
Related Issues (20)
- Bluetooth not working, HOT 1
- Problem: Low memory error while running G-code HOT 3
- Problem: if i conect on webserver while executing a job from memory , job halts HOT 11
- Problem: ALARM 9 homing fail HOT 13
- Podłączenie step_pin: gpio.12 do driverTB6600 (wspólna anoda)- ESP32 not boot LED blink HOT 8
- Feature: Get GRBL version printout HOT 1
- Starting a message with the /R option is displayed as "noradio" in the configuration with wifi: Grbl 3.8 [FluidNC v3.8.1 (noradio).
- Jaki czytnik karta micro SD działa prawidłowo na gołym ESP32 38 PIN HOT 1
- Feature: 4-axis control on webui HOT 1
- Problem: Motors won't lock with 4x TMC2209 board HOT 20
- Problem: FluidNC Crashing Randomly. HOT 1
- Problem: 6x CNC Control does not start. HOT 5
- Problem: I am using Fysetc E4, there is a voltage between ground laser enable and PWM pin HOT 12
- Problem: GCode Logic has problems and throes errors HOT 6
- Problem: Crash/stalling during Web UI page reload HOT 6
- Feature: The ability to exit out of a Macro mid script HOT 13
- Problem: '$$' does not return '$32' for the laser configuration HOT 2
- Problem: Config Dump ($CD=config.yaml) Adds Invalid Lines to YAML, increases time to connect HOT 3
- Problem: Crash and Reboot after 20-30 minutes HOT 5
- Problem: Steppers Don't Rotate HOT 14
Recommend Projects
-
React
A declarative, efficient, and flexible JavaScript library for building user interfaces.
-
Vue.js
🖖 Vue.js is a progressive, incrementally-adoptable JavaScript framework for building UI on the web.
-
Typescript
TypeScript is a superset of JavaScript that compiles to clean JavaScript output.
-
TensorFlow
An Open Source Machine Learning Framework for Everyone
-
Django
The Web framework for perfectionists with deadlines.
-
Laravel
A PHP framework for web artisans
-
D3
Bring data to life with SVG, Canvas and HTML. 📊📈🎉
-
Recommend Topics
-
javascript
JavaScript (JS) is a lightweight interpreted programming language with first-class functions.
-
web
Some thing interesting about web. New door for the world.
-
server
A server is a program made to process requests and deliver data to clients.
-
Machine learning
Machine learning is a way of modeling and interpreting data that allows a piece of software to respond intelligently.
-
Visualization
Some thing interesting about visualization, use data art
-
Game
Some thing interesting about game, make everyone happy.
Recommend Org
-
Facebook
We are working to build community through open source technology. NB: members must have two-factor auth.
-
Microsoft
Open source projects and samples from Microsoft.
-
Google
Google ❤️ Open Source for everyone.
-
Alibaba
Alibaba Open Source for everyone
-
D3
Data-Driven Documents codes.
-
Tencent
China tencent open source team.
from fluidnc.