Comments (17)
I only used your new version 2.3.1.
The 2.3 I have not tested. I can do this today.
Yes, here is Germany.
from kiss_osd.
How did you update the OSD? With Arduino? Or XLoader?
If Arduino: What version did you use?
from kiss_osd.
Another question: What camera do you use? Is it a NTSC or PAL camera?
from kiss_osd.
from kiss_osd.
My guess is that the PAL Autodetection does not work. The camera might switch from NTSC to PAL during startup which could confuse the auto detect.
Can you please try the attached version. I have increased the delay during startup by 10 times which should make the auto detection more stable.
If that does not work I can send you a version which has PAL enforced.
KISS_OSD_CONFIG V2.3.1 BETA.zip
from kiss_osd.
from kiss_osd.
Then try this one, this one is forced to PAL.
If you get something like "no connection to kiss fc" - try swapping the rx and tx wires.
from kiss_osd.
Yes, this works.
Greetings
from kiss_osd.
When you are done with the config tool, let me know if this OSD version works.
from kiss_osd.
Very good, it works.
All kiss parameters are correct and can be changed !!
Very good is that I can now some things in the program turn on and off.
Fyi: In the config program, some icons were displayed, although icons were switched off.
In the main program, however, it is correct.
Thank you for your good work, this is very helpful.
Greetings Frank
from kiss_osd.
First of all: Thank you for the donation!
I will check the icons in the config tool for the next release.
Question: Did you use the original KISS OSD V2.3 or the one I sent you for it to work?
Aus Deutschland?
from kiss_osd.
V2.3 brauchst Du nicht testen, wird wahrscheinlich dasselbe Problem haben wie vorher.
Kannst Du mir bitte einen Gefallen tun und die Version im Anhang testen? Sollte die nicht funktionieren flashe bitte wieder die vorherige und gib mir (in jedem fall) kurz Bescheid.
from kiss_osd.
okay in deutsch geht es schneller, fein.
Also, 2.3.1.Beta läuft exakt wie die alte 2.3.1 passt also.
Noch ein kleiner Bug?? Im State- Menü(nach dem Flug) wird für ESC3 fast! immer eine völlig falsche Drehzahl angegeben, selbst bei der Startdrehzahl, ohne Airmode! Z.B. irgendwas zwischen 20-50.000 statt 2000 bei den restlichen ESCs. Die weiteren Daten wie Strom, Temp sind korrekt.
Das ist übrigens auch in V2.2 so.
Übrigens: Ich hoffe dass Kiss irgendwann mal den Frsky-RSSI durchreicht, der wäre schon nett in der Brille.
Grüße
from kiss_osd.
Super, dann funktioniert die neue PAL/NTSC Autodetektion ;)
ESC3: Das ist leider kein bug in meinem OSD, sondern ein Problem mit Deinem ESC3. Du kannst versuchen die ESCs nochmal zu flashen, aber bei mir hat das nicht geholfen. Ich habe einen ESC der gar keine Telemetriedaten mehr liefert ansonsten allerdings einwandfrei funktioniert.
RSSI: Da brauche Ich Deine Unterstützung: Poste bitte in der KISS FC Facebook oder rc-groups das Du dieses Feature gerne hättest (am besten beide). Ich habe das auch schon angefragt, ist aber bisher auf taube Ohren gestoßen :(
Vielen Dank fürs testen, Du bist als beta Tester angeheuert :)
from kiss_osd.
Danke für das schnelle Feedback, ich bin erst heute wieder verfügbar.
Der KISS-Fehler mit den ESCs ist ja interessant. Vielleicht ist das ja auch die Ursache für die falsche Kapazitätsanzeige vom FC. In der Taranis muss ich dafür einen Korrekturfaktor von +30% ansetzen!
Bezüglich RSSI werde ich mit maulen, ist mir wichtig.
Beta-Tester, jederzeit !
Schöne Ostern
from kiss_osd.
from kiss_osd.
Yes
from kiss_osd.
Related Issues (20)
- Polulu FTDI drivers installation not working HOT 3
- GPS Arrow with mr Steele pdb HOT 2
- AIKON 4 in 1 current sensor is not working on micro minim OSD HOT 4
- No Video Feed No OSD HOT 4
- Steele PDB - No connection to FC HOT 2
- Req: Digital font. HOT 10
- KISS OSD and new KISS V2 Firmware RC36i Camera Control Issue HOT 8
- icons HOT 1
- No connection to Kiss FC w/ steele pdb (Kiss FC V1) HOT 2
- Setting VTX Power via OSD (Wolf PDB with KISS FC v1) HOT 5
- Mr. Steele pdb props all over screen HOT 3
- Correct settings for rssi Steele pdb HOT 6
- mr steele pdb HOT 2
- No Display menu option in OSD menu HOT 5
- No connection to kiss fc HOT 5
- Steele pdb V1 impossible to update firmware HOT 3
- Xloader upload failed HOT 2
- No Mah drawn on OSD HOT 4
- All motors spinning in the same direction (right) HOT 2
- missing SET ITEMSfrom my config menu HOT 1
Recommend Projects
-
React
A declarative, efficient, and flexible JavaScript library for building user interfaces.
-
Vue.js
🖖 Vue.js is a progressive, incrementally-adoptable JavaScript framework for building UI on the web.
-
Typescript
TypeScript is a superset of JavaScript that compiles to clean JavaScript output.
-
TensorFlow
An Open Source Machine Learning Framework for Everyone
-
Django
The Web framework for perfectionists with deadlines.
-
Laravel
A PHP framework for web artisans
-
D3
Bring data to life with SVG, Canvas and HTML. 📊📈🎉
-
Recommend Topics
-
javascript
JavaScript (JS) is a lightweight interpreted programming language with first-class functions.
-
web
Some thing interesting about web. New door for the world.
-
server
A server is a program made to process requests and deliver data to clients.
-
Machine learning
Machine learning is a way of modeling and interpreting data that allows a piece of software to respond intelligently.
-
Visualization
Some thing interesting about visualization, use data art
-
Game
Some thing interesting about game, make everyone happy.
Recommend Org
-
Facebook
We are working to build community through open source technology. NB: members must have two-factor auth.
-
Microsoft
Open source projects and samples from Microsoft.
-
Google
Google ❤️ Open Source for everyone.
-
Alibaba
Alibaba Open Source for everyone
-
D3
Data-Driven Documents codes.
-
Tencent
China tencent open source team.
from kiss_osd.